The Coil Coating Process: Pretreatment, Primer, Topcoat and Cure.
Prepainted coil is coated flat, in a continuous run, before anyone forms it. Knowing the order of the stages explains why some questions belong in the specification and others cannot be answered from a color chip.
Key takeaways
- The general sequence is cleaning, pretreatment, primer, cure, topcoat, cure and cooling, then rewinding.
- Each stage has a job. A defect at one stage can show up later as a problem at another.
- This post describes the general process. It does not describe any one line.
- Ask the coater to state the pretreatment, the primer and topcoat system, and the evidence for the properties you need.
What happens before the paint goes on?
A coil is unwound and joined to the one ahead of it so the line can run continuously. The strip is then cleaned to remove rolling oils and surface contamination. Cleaning matters because coatings bond to the surface that is actually there, not to the surface that was intended.
Pretreatment follows. This is a thin chemical layer applied to the cleaned metal to prepare it for the primer. The chemistry can differ between coaters and between substrates, so the useful question is not whether pretreatment is applied but which pretreatment, and what evidence supports it for your use.
What do primer and topcoat each do?
| Stage | Role | Question to ask |
|---|---|---|
| Cleaning | Removes oils and contamination | How is surface condition checked? |
| Pretreatment | Prepares the metal for the primer | Which pretreatment is applied to your alloy? |
| Primer | Bonds to the pretreated surface and carries the topcoat | Which primer goes with your topcoat system? |
| Topcoat | Provides color, gloss and the exposed surface | Which system, and what test reports support it? |
| Cure | Hardens the applied coating in an oven | Is cure verified, and how? |
Orbit names these coating systems: PE, HDPE, PVDF, PU, PUPA, Epoxy, Acrylic and Epoxy-PE. The system is chosen against the exposure and the specification. The PE, PVDF and HDPE comparison covers three of them.
Why is cure a specification topic?
A coating reaches its intended properties when it is cured. Under-cured film can behave differently in solvent and in forming than a fully cured one. This is why a solvent rub test is used as an indicator of cure, as the test results guide explains, and why the result needs the solvent and the number of rubs stated.
You do not need to write oven temperatures into an order. You do need to ask what evidence the coater holds that cure was achieved, and ask for it by test name.
Where do problems from one stage show up later?
Adhesion loss at a bend can trace back to cleaning, pretreatment or cure rather than to the topcoat. Color variation between lots can trace to application or cure conditions as well as to pigment. Diagnosing this needs records, which is why traceability of the lot matters. A mill test certificate and a lot tag are a starting point for an investigation.
When a problem appears after forming, tell the supplier the lot reference, the forming operation and the bend radius. Those facts help narrow the search.
What can a coater's description leave out?
A one-line description such as "PVDF, white" says little. It can leave out the pretreatment, the primer, the number of coats, the film thickness on each coat, the gloss level, the backcoat (reverse-side) requirement and the test evidence. Each omission is a question for the supplier, and the answers belong in the specification so that the delivered coil can be checked against them.
Coating architectures vary, and the sequence described in this post is an illustration, not a description of any one line. The backcoat is part of the architecture, so state what the reverse side needs.
Film thickness is worth asking about by name. It can affect how other test results behave, so a thickness without a measurement method and a reporting basis is hard to compare between suppliers.
Prepainted coil or painting after fabrication?
The coil process coats the strip before forming, so the coating must survive the forming. Coating after fabrication applies paint to the finished part. The choice depends on part shape, volume and the finish required, and neither route is right for every product. If you form after coating, the forming questions in your specification carry more weight, especially bend radius and T-bend result.
What should the specification say?
- The alloy, temper and gauge of the substrate
- The coating system and color, with gloss level
- The tests you want reported and the standards they follow
- The forming operation, so the coating can be checked against it
For coil coated sheet and strip, EN 1396, Aluminium and aluminium alloys, Coil coated sheet and strip for general applications, Specifications, covers coil coated sheet and strip for general applications, coated with liquid or powder paints.
A request for quotation that covers these lets Orbit respond with answers and questions. Coated coil is up to 1.60 mm thick and 1350 mm wide, so check your gauge and width fit that range.
How do you check a sample against the process?
A sample panel or a short length of coil lets you test what the paperwork describes. Form it at your bend, check the coating at the bend edge, and compare color under the lighting your project will use. Keep the sample with its lot reference, so that a later delivery can be compared with the one you approved. If the sample and the delivery differ, the lot reference is what allows the difference to be traced back through the stages above.
Common questions
Does every coater use the same pretreatment?
It can differ. Ask the supplier to state the pretreatment applied.
What is the primer for?
It bonds to the pretreated metal and carries the topcoat. The primer and topcoat should be a matched system.
Can I see Orbit's line parameters?
Line parameters are not published in this post. Ask in your RFQ for the information your review needs.
Why does cure matter if the color looks right?
Appearance alone may not show cure. Tests such as solvent rub are used to indicate it, with the solvent and rub count stated.
References
- What coated aluminum coil test results actually measure: tests that bear on cure, adhesion and forming.
- CEN: EN 1396, Aluminium and aluminium alloys, Coil coated sheet and strip for general applications, Specifications: coil coated sheet and strip for general applications, coated with liquid or powder paints.
- Orbit prepainted aluminum coil: the product page for coated coil.
Specifying a coated coil?
Send substrate, coating system, color and finish, gauge, width and forming operation. We respond to RFQs within one business day.
