Blog.

Notes on coil specification and coating selection, written for buyers and specifiers.

5xxx Aluminum Coil: Where 5005, 5052 and 5754 Fit

What the 5xxx magnesium series is, how 5005, 5052 and 5754 differ on paper, and the questions that decide whether a formed, coated part needs one of them.

Read the article

Aluminum vs Galvanized Steel Coil: Weight, Corrosion, Cost

Aluminum vs galvanized steel coil compared on weight, corrosion behavior, cost drivers and forming, for buyers choosing a substrate for coated products.

Read the article

Best Aluminum Alloy for Bending: 1xxx, 3xxx or 5xxx?

The best aluminum alloy for bending depends on series and temper. How 1xxx, 3xxx and 5xxx compare for forming, and what to ask about bend limits.

Read the article

3xxx Aluminum Coil: Where 3003 and 3105 Fit

What the 3xxx series is, how to decide whether 3003 or 3105 coil suits a formed, coated part, and when to look at 1xxx or 5xxx instead.

Read the article

Reading Yield Strength, Tensile Strength and Elongation on an Aluminum Coil Datasheet

What tensile strength, yield strength and elongation mean on an alloy datasheet, how O and H tempers change them, and how to tell a requirement from a typical value.

Read the article

1050 and 1100 Aluminum Coil: When Pure Aluminum Fits

1050 and 1100 are 1xxx alloys, the commercially pure end of the 1xxx, 3xxx and 5xxx series Orbit rolls into coil: high corrosion resistance and formability, low strength, strengthened by cold work. Where pure aluminum fits and where it does not.

Read the article

Aluminum Coil Gauge and Alloy Selection for Roll-Forming and Roofing

A retail gauge chart is not enough for a roll-formed roofing profile. How gauge, alloy and temper interact in a coil roll-forming context, and how to specify all three together.

Read the article

3003 vs 5052 Aluminum: Which Alloy for Outdoor Coil Coating Applications

3003 and 5052 are both outdoor-capable coil alloys. How environment, panel size and forming requirements decide which one fits a cladding specification.

Read the article

5052 Aluminum Coil for Coating: Properties, Thickness, and Finish Options

What 5052 aluminum coil offers for coil coating: general alloy characteristics, the thickness and width ranges available, temper options, and the coating and finish systems it runs.

Read the article

Choosing Aluminum Temper for Coil Coating and Forming

For coil that is coated and then formed: how O and H-series tempers trade bend radius against dent resistance, and how to state temper on the order.

Read the article

1xxx, 3xxx, and 5xxx Series Aluminum: What the Numbers Mean for Coil Buyers

What the first digit of a wrought aluminum alloy number tells you, and how the 1xxx, 3xxx and 5xxx families differ for coil coating specification.

Read the article

3105 vs 3003 Aluminum: Mechanical Properties and Coil Coating Applications

3003 and 3105 are related 3xxx-series alloys with different roles in coil coating, and 3105 is the substrate behind Orbit's confirmed recycled-content example. How to choose between them.

Read the article

5052 vs 6061 Aluminum: Choosing the Right Alloy for Coil Coating

5052 is a non-heat-treatable coil alloy, 6061 is a heat-treatable structural alloy. What separates them, why coil coating favors one, and how to read a spec that names the other.

Read the article

Aluminum Gutter Colors: How to Specify and Match Coil

Aluminum gutter coil colors: how gutter coil color is specified, RAL and custom matching, and how to keep gutters and downspouts matching over time.

Read the article

Aluminum vs Steel Trailer Panels: Weight and Corrosion

Aluminum vs steel trailer panels compared: weight, corrosion, repair and finish, and what each means for a body builder choosing panel material.

Read the article

Galvalume vs Galvanized Steel: How the Coatings Differ

Galvalume vs galvanized steel: what each metallic coating is, how they behave in corrosion, and where each is used. An education guide for coil buyers.

Read the article

PPGI vs PPGL: Prepainted Galvanized vs Galvalume Steel

PPGI vs PPGL explained: what the two prepainted steel terms mean, how their metallic substrates differ, and where buyers use each.

Read the article

Standing Seam Aluminum Roof: Specifying the Coil

Standing seam aluminum roof systems start with coil. What roll formers specify: alloy, temper, thickness, width, coating and color.

Read the article

What Does Embossed Mean? Embossed Aluminum Explained

Embossed means a raised pattern pressed into a surface. Embossed vs debossed, patterns used on aluminum sheet and coil, and why fabricators use it.

Read the article

RAL Reference or Custom Color Match: What to Send and How to Approve

How to specify a RAL color or request a custom match on prepainted aluminum coil: what to send, what to agree on measurement, and how to keep an approved reference.

Read the article

Which Functional Coating for Which Building?

How easy-clean, silver-ion antibacterial and NIR-reflective thermal coatings work, how each is judged in general terms, and what to specify when requesting a functional coating on aluminum coil.

Read the article

PVDF Aluminum Coil for Facade and Rainscreen Cladding: Specification Notes

What to specify when PVDF-coated aluminum coil goes into facade and rainscreen cladding: the 70:30 binder, color retention, panel-to-panel consistency, coastal exposure, and ACP versus single-skin tray.

Read the article

Distributors and Service Centers: Sourcing Coated Aluminum Coil at Scale

What a distributor needs from a mill relationship: consistent supply, lead-time reliability, and integrated rolling, coating and recycling as a differentiator.

Read the article

How to Specify Prepainted Aluminum Coil: A Buyer's Checklist

A practical checklist covering what to specify in a prepainted aluminum coil RFQ: alloy, gauge, width, coating system, finish, quantity and lead time.

Read the article

Specifying Prepainted Aluminum Coil for License Plates

Reflectivity and finish consistency requirements, gauge, and why prepainted coil suits stamped license plate production.

Read the article

Aluminum Coil for Rolling Shutters: Alloy and Thermal Coating Options

Alloy selection for shutter slat forming and thermal-management coating options for rolling shutter coil, a more established building product in Europe than in North America.

Read the article

Truck and Trailer Panels: Specifying Painted Aluminum Coil

Coating durability under road exposure and washing, alloy choice for panel forming, and gauge for weight-sensitive fleet applications.

Read the article

Aluminum Coil for Metal Roofing: Coating Systems and Finish Options

Coating system selection for metal roofing specifically: standing seam versus other profiles, and how color and finish retention play out over a roof's service life.

Read the article

Aluminum Composite Panel Coil: What Fabricators Specify

Coil requirements for ACP core-skin manufacturing: gauge, coating adhesion, and color consistency across a production run.

Read the article

Blank Aluminum Coil for Signage: Substrate and Coating Requirements

What sign fabricators need from substrate coil: flatness, finish options, and which coating systems hold up for outdoor signage.

Read the article

Choosing a Coating System for Exterior Aluminum Coil: PE vs PVDF vs HDPE

The general, source-verified differences between PE, HDPE and PVDF coil coating systems: durability, forming flexibility, and which exposure each one generally fits.

Read the article

Gutter Coil Gauge, Alloy and Coating: A Specification Guide

What a roll-former or fabricator needs to specify when sourcing aluminum gutter coil: gauge range, alloy choice for forming, and which coating systems hold up under continuous exposure.

Read the article

Aluminum Sheet vs Plate: Where the Thickness Line Falls

Aluminum sheet vs plate: where US practice draws the thickness line, how each is used, and how coil-based sheet fits into a fabricator's order.

Read the article

The Coil Coating Process: Pretreatment, Primer, Topcoat and Cure

A plain walk through the coil coating sequence, what each stage is for, and which questions to ask a coater at each step.

Read the article

Coil Weight and Length: A Worked Arithmetic Example for Aluminum Coil

How to estimate strip length, coil weight and outside diameter from thickness, width and density, with two worked examples and a check against a 6.5 MT minimum order.

Read the article

Receiving, Storing and Handling Coated Aluminum Coil

How coated coil is packed for export, and what to do on arrival: inspection, lifting, indoor storage, condensation, and keeping intact, dry wrapping on until the coil goes on the line.

Read the article

Master Coil, Slit Coil or Cut-to-Length Sheet: How to Choose

When to buy master coil, slit coil or cut-to-length sheet, and what leveling and edge trimming change. A buyer's guide to choosing the form that fits your line.

Read the article

Mill Test Report: How to Read an Aluminum Coil MTR

How to read a mill test report for aluminum coil: check alloy, temper, chemistry, mechanical properties, dimensions and lot reference against the order.

Read the article

How coil gauge and coating choice affect metal roof lifespan

Gauge governs how a metal roof holds its shape, coating governs how long it holds its color. What each decision changes, and how to specify both.

Read the article

Have a specification to price?

Send your application, substrate, alloy, gauge, width, coating, color, quantity and destination. We respond to RFQs within one business day.

Request a Quote