Finish · Directional pattern

Brushed aluminum sheet and coil.

Brushed aluminum sheet has a fine, straight line pattern that runs in one direction across the surface. That look can come from two different routes: a brushed-look pattern built into a paint film on coated coil, or lines cut into the bare metal by mechanical brushing. Orbit supplies a brushed finish on coated aluminum from Aqaba, Jordan, and confirms the route for each order.

  • Coated coil up to 1.60 mm thick
  • Up to 1350 mm wide
  • Details on request
  • MOQ 6.5 MT

Printed brushed look or mechanically brushed metal?

The two can look alike from a short distance, but they are made differently and behave differently in use.

Brushed-look coated coil compared with mechanically brushed metal (general practice)
PointBrushed-look coated finishMechanically brushed metal
Where the lines areIn the paint film, over a base coatCut into the metal surface itself
How it is madeThe line pattern is applied on the coil coating line, usually under a clear coat; methods vary by lineThe surface is run against abrasive brushes or belts that leave fine parallel lines
ColorAny base color the coating system allows, including metallic tonesThe natural color of the metal, unless a tinted clear coat is added
Surface protectionComes from the coating systemBare brushed metal marks easily, so it is often sealed with a clear coat
Consistency along the coilSet by the coating line, so it repeats along the stripDepends on the brushing process and the metal surface

For a painted brushed finish, the durability outdoors depends on the coating system, not on the pattern. For mechanically brushed metal, it depends on how the metal surface is protected after brushing. Either way, ask which route an offer is based on before comparing prices, because the two are not the same product.

Orbit lists brushed among its coated aluminum finishes. Whether a brushed order is supplied as a printed pattern or a mechanical finish is confirmed per order, with details on request.

Where is brushed aluminum coil used?

In the wider market, brushed coil goes into parts where a metal look is wanted but a bare mill surface would be too plain or too easy to mark. General uses include:

  • Interior wall and ceiling panels: lobbies, lifts and shopfitting, where the line pattern hides light handling marks better than a smooth gloss.
  • Composite panels: skins for panels that need a metal appearance on one face.
  • Signage: sign faces and trays where a brushed background suits printed or cut lettering.
  • Trim and appliance parts: strips, kick plates and covers cut from sheet.

Brushed aluminum sheet is cut from the same coil, so a fabricator can order master coil, slit coil or cut sheet depending on the line. Because the pattern has a direction, the way panels are cut from the coil decides how the lines run on the finished part. For a metal sheen without lines, compare the metallic aluminum finish.

What to approve on a brushed aluminum sheet sample

A brushed finish is a directional finish, so a RAL number or a color name is not enough to define it. Approve a physical sample before the production run and check these points:

  • Direction: whether the lines run along the coil length or across it, and how that maps onto your cut and formed parts.
  • Pattern: how fine or coarse the lines are, and how even they look across a full panel width.
  • Gloss: the gloss level of the top layer, which changes how strongly the lines show.
  • Color: the base color and any tint, judged under a light source both sides agree on, with the sample held the same way for each viewing.

On a facade or a long run of interior panels, mark the direction on every panel and install them all the same way round. Panels turned through 90 or 180 degrees can look like a different shade. Keep one elevation from the same production batch where possible; every batch ships with material certificates.

Orbit brushed coated coil: confirmed supply data
SubstrateAluminum in 1xxx, 3xxx and 5xxx series alloys. 3105 is the main coated substrate.
Coated thicknessUp to 1.60 mm
Coated widthUp to 1350 mm
Coating systemsPE, HDPE, PVDF, PU, PUPA, Epoxy, Acrylic, Epoxy-PE. System for a brushed order confirmed per order.
Brushed routePrinted or mechanical, confirmed per order. Details on request.
Warranty5 to 20 years, depending on application and environment
Minimum order6.5 MT, typically 6 MT per color on coating

Brushed coil is supplied within Orbit's prepainted aluminum coil range, and Orbit replies to an RFQ within one business day.

Brushed finish questions.

Is a brushed aluminum finish painted or mechanically brushed?

Both routes exist in the market. A brushed-look finish on coated coil is a line pattern in the paint film, while mechanically brushed metal has lines cut into the bare surface. Orbit confirms which route applies to a brushed order per order, with details on request.

Can brushed aluminum sheet be supplied in colors other than silver?

A brushed-look coated finish sits over a base coat, so other base colors are possible within the coating system. Mechanically brushed metal shows the natural metal color unless a tinted clear coat is used. Color and finish combinations are confirmed per order against a physical sample.

Why do brushed panels look different shades on the same wall?

The lines reflect light differently depending on their direction. Panels installed with the lines turned through 90 or 180 degrees can look lighter or darker, so mark the direction on each panel and install them all the same way round.

Is a brushed finish suitable for outdoor use?

A painted brushed finish can be, when the coating system suits the exposure. State the site conditions in your RFQ and confirm the coating system and warranty terms for the brushed finish at quote stage.

What is the minimum order for a brushed finish?

The minimum order is 6.5 MT, and coating is typically run at 6 MT per color.

Brushed finish to quote?

Send the application, a sample of the look you need, line direction, alloy, thickness, width, quantity, site exposure and destination. We respond to RFQs within one business day.

Request a Quote