Reference · Physical properties
Aluminum melting point: pure aluminum and alloys.
The aluminum melting point is 660.323 °C (1220.58 °F, 933.473 K) for pure aluminum. That value is the freezing point of aluminum, a defining fixed point of ITS-90, the international temperature scale. Aluminum alloys generally do not melt at one temperature: they melt over a range, so for process work you need the data for the specific alloy.
- 660.323 °C
- 1220.58 °F
- 933.473 K
What is the melting point of aluminum?
Pure aluminum melts, and freezes, at 660.323 °C. At that temperature solid and liquid aluminum are in equilibrium, and the temperature stays constant while the metal changes state. Because that plateau is so reproducible, the freezing point of aluminum is one of the defining fixed points of the International Temperature Scale of 1990 (ITS-90), the scale national laboratories use to calibrate thermometers. NIST Technical Note 1265, on realizing ITS-90, gives it as 933.473 K (660.323 °C).
| Unit | Value | How it is obtained |
|---|---|---|
| Kelvin | 933.473 K | ITS-90 fixed point value (NIST Technical Note 1265) |
| Celsius | 660.323 °C | 933.473 K minus 273.15 |
| Fahrenheit | 1220.58 °F | 660.323 x 1.8 + 32, rounded to two decimals |
The Fahrenheit conversion is plain arithmetic: 660.323 x 1.8 = 1188.58, and 1188.58 + 32 = 1220.58 °F. In everyday engineering the value is often rounded to 660 °C (1220 °F), which is close enough for most purposes outside temperature calibration.
Why sources give slightly different values
You may see 660.3 °C, 660.32 °C or a value in kelvin that differs in the second decimal place. The NIST Chemistry WebBook, for example, lists a catalog value for the fusion temperature of aluminum of 933.45 K, which is 660.30 °C. The differences come from rounding and from the purpose of each source: a general data compilation gives a nominal value, while the ITS-90 fixed point is defined for metrology, with the metal at very high purity. For reference work the ITS-90 value, 660.323 °C, is the one to quote.
Do aluminum alloys melt at the same temperature?
No. The single melting point applies to pure aluminum. An alloy contains other elements, such as manganese in the 3xxx series or magnesium in the 5xxx series, and a mixture of elements usually melts over a temperature range rather than at one point. Metallurgists describe that range with two temperatures:
- Solidus: the temperature at which the alloy starts to melt on heating.
- Liquidus: the temperature at which it is fully liquid.
Between the two, the metal is partly solid and partly liquid. The width and position of the range depend on the alloy and its exact composition, so they differ between grades in the same series. This page does not list solidus and liquidus temperatures for individual alloys. If a process depends on them, such as brazing, welding or any heat treatment close to the melting range, ask the producer for the data for the specific alloy and confirm it against the alloy's composition.
Why the melting point matters for coil buyers
Recycling and casting at the mill
Every aluminum coil starts as molten metal. At an integrated mill, scrap and other feedstock are melted, the melt is brought to the required alloy composition and then cast, and the cast metal is rolled down to coil. Orbit does this in Aqaba, Jordan: aluminum recycling, casting, hot and cold rolling and coil coating all take place at one site, and the metal is melted and cast by Orbit in Jordan. Recycled content of about 75% is achievable on select coated coil, for example 3105 substrate with a PUPA coating, confirmed per order and traceable to the cast batch. The closed loop from scrap back to coil describes how recycled metal returns to production.
Coating cure is a different temperature regime
Buyers of prepainted coil sometimes ask whether the paint oven affects the metal. Coil coatings are cured in an oven on the coating line, at temperatures far below the melting point of aluminum. The oven cures the paint film and the metal stays solid. The cure heat can still reduce some of the strength gained by strain hardening, which is why tempers for coated coil are written as H4x (strain hardened, then heated during the paint cure), as the aluminum temper chart explains. State the temper you need after coating when strength matters. The guide to the coil coating process from pretreatment to cure explains each stage of the line.
Rolled and coated coil from Orbit
Orbit supplies aluminum coil rolled from metal cast in Jordan in 1xxx, 3xxx and 5xxx series alloys, 0.20 to 2.00 mm thick and up to 1650 mm wide, with a certificate of origin available and a material certificate with every batch. Physical data for the alloy supplied is available on request. For the weight side of the same material, see the page on the density of aluminum alloys.
Sources
- NIST Technical Note 1265, Guidelines for Realizing the International Temperature Scale of 1990 (ITS-90), National Institute of Standards and Technology: freezing point of aluminum, 933.473 K (660.323 °C).
- NIST Chemistry WebBook, National Institute of Standards and Technology, entry for aluminum: fusion temperature catalog value, 933.45 K.
Melting point questions.
What is the melting point of aluminum in Fahrenheit?
1220.58 °F for pure aluminum. It comes from the Celsius value: 660.323 x 1.8 + 32 = 1220.58.
What is the melting point of aluminum in Celsius?
660.323 °C for pure aluminum. This is the freezing point of aluminum, a defining fixed point of the International Temperature Scale of 1990 (ITS-90).
Do aluminum alloys melt at a single temperature?
Generally no. Alloys melt over a range, between a solidus and a liquidus temperature, instead of at a single point. The range depends on the alloy and its composition, so ask for the data for the specific alloy when a process depends on it.
Is the melting point of aluminum the same as its freezing point?
For pure aluminum, yes. Solid and liquid are in equilibrium at 660.323 °C, so the metal melts on heating and freezes on cooling at the same temperature.
Does the paint curing oven come close to melting aluminum coil?
No. Coil coatings are cured at temperatures far below the melting point of aluminum, so the metal stays solid. The cure heat can reduce some of the strength from strain hardening, which is why coated-coil tempers are written as H4x.
Need alloy data with your coil?
Send the alloy, thickness, width, quantity and destination, and say which physical data you need. We respond to RFQs within one business day.
