Aluminum gutter coil for gutter makers and distributors.

Aluminum gutter coil in HDPE, PVDF or PE and any RAL color, slit to the width your gutter machine runs. Corrosion-resistant coil for gutters and downspouts, with coatings matched to coastal or inland exposure.

  • Alloy 3xxx
  • HDPE / PVDF / PE
  • Up to 1350 mm coated
  • RAL or custom color

Application

Coating by climate.

Gutters cycle wet and dry. HDPE covers durable, cost-effective rainware; PVDF suits the coast and long-term color hold. Mill-finish coil is available where gutters are painted on site or left natural.

HDPEPVDFPEMill-finish or prepaintedSlit to gutter width
Aluminum gutter and downspout along a house roofline

Coil for on-site gutter machines.

Seamless gutter machines need coil that runs true and holds gauge so profiles form cleanly and lengths stay straight.

Prepainted aluminum coil

Coil specification.

Indicative ranges, gutter width confirmed per order
CoatingsHDPE, PVDF, PE (or mill-finish). Two-side coating is available on request.
Thickness0.20 to 2.00 mm rolled; up to 1.60 mm coated (gutter gauge on request)
WidthUp to 1650 mm (coating up to 1350 mm); slit to width
Coil weightUp to 10 tonnes
Minimum order6.5 MT (±10%)
ColorRAL or custom match (available)
Warranty5 to 20 years by application and environment

Buyer guidance

Recommended specification.

A starting point for gutter coil. Treat these as guidance, not a fixed datasheet.

Recommended specification
Alloy3xxx
CoatingHDPE or PE
ThicknessThickness is set by your specification and confirmed per order; Orbit rolls 0.20 to 2.00 mm, coated up to 1.60 mm.
ColorFull RAL
HandlingProtective film for transit

Exact alloy, gauge and coating are confirmed per order, share your spec in an RFQ.

Gutter coil supply for makers and distributors

Orbit supplies two kinds of gutter buyer. Gutter makers and installers run the coil through a roll-former, either a factory line for sectional gutters and downspouts or a portable machine on site. Distributors stock coil in a range of colors and sell it on to installers. Both need the same things from the mill: steady gauge, a coating that survives the bend, and color that matches from one order to the next.

We roll master coil up to 1650 mm wide (coated up to 1350 mm) and slit it in house to the strip width your machine takes. Slit widths are quoted per order against your machine, not from a fixed list; see slitting and cut-to-length for how slitting works. The minimum order is 6.5 MT, typically 6 MT per color on coated coil, which lets a distributor build a color range over several orders.

If you are comparing gutter coil suppliers, ask each one for the alloy and temper, the coating system and film thickness, the color reference, the warranty terms and the material certificate for the batch. Orbit sends a material certificate with every batch and replies to RFQs within one business day.

Why aluminum gutters

Gutters are in constant contact with water, so corrosion resistance is paramount; aluminum suits residential and light-commercial gutters because it does not rust, though it can corrode in contact with copper or unprotected steel, so compatible fasteners matter; seamless gutters are roll-formed on site from coil. In North American gutter and fascia work, related prepainted coil is sold as trim coil, usually in thinner gauges.

Design and forming

Clean T-bend performance is needed because seamless gutter machines roll-form the coil into a profile on site, bending the painted surface tightly, and a brittle coating would crack at the bend. Consistent color across batches matters because gutters and downspouts are ordered as a matched set and installed side by side. As a general guide, coastal installations favor PVDF for color hold, while general inland use is well served by lower-cost HDPE.

How thick should gutter stock be?

Thickness is set by your specification and confirmed per order against your profile and machine; Orbit rolls 0.20 to 2.00 mm, coated up to 1.60 mm. In North America the thickness is often quoted in decimal inches rather than millimeters; the sheet metal gauge chart converts between them. The gutter coil gauge, alloy and coating guide explains how gauge, alloy and coating work together.

Coatings and colors for aluminum gutter coil

The coating follows the exposure. Every coated option runs in any RAL color or a custom match to your sample.

Coating options for gutters and downspouts
OptionGutter use
HDPEDurable, cost-effective rainware for general inland exposure
PVDFCoastal sites and long-term color hold
PEMilder exposure and budget rainware
Mill finishGutters painted on site or left natural

For a distributor, color consistency is the point that decides repeat business: an installer who adds a downspout next year expects it to match the gutter. Give us a RAL number or a physical sample, and keep the same reference across orders. Two-side coating is available where the inside of the gutter will be seen.

Quality & compliance

Testing and documentation.

Certified management systems

Orbit's management systems are certified to ISO 9001 (quality), ISO 14001 (environment) and ISO 45001 (occupational health and safety).

Tests that matter here

Coated coil can be tested for salt spray, T-bend flexibility and adhesion; test reports for a given order are available on request. See quality & certifications for how this is documented.

Documentation with the batch

Material certificates accompany every batch; ASTM and EN references are available on request.

Related applications: Roofing · Cladding

Gutter coil questions.

Is gutter coil the same as aluminum trim coil?

They overlap. In North America, the prepainted aluminum coil used for gutters, downspouts and fascia is commonly called gutter coil or trim coil. Orbit supplies it corrosion-resistant, in any RAL color, in gutter gauges.

What aluminum is used for gutters?

Gutters use coated aluminum coil, corrosion-resistant and matched to any RAL color.

Do you supply aluminum gutter coils to distributors?

Yes. Orbit supplies master and slit coil to gutter makers and distributors. The minimum order is 6.5 MT, typically 6 MT per color on coated coil.

Can you slit coil to my gutter machine width?

Yes. Orbit slits in house; the slit width is confirmed per order against your machine.

Which coating for coastal gutters?

PVDF is an option for coastal exposure; HDPE suits general inland use.

Can you match my gutter color?

Yes. Orbit matches any RAL or custom color.

What thickness is typical for gutters?

Thickness is set by your specification and confirmed per order; Orbit rolls 0.20 to 2.00 mm, coated up to 1.60 mm.

What is the minimum order?

The minimum order is 6.5 MT, plus or minus 10 percent.

What to send with your RFQ.

Include these and we can return a coil specification and quote without back-and-forth.

  • Application and substrate (aluminum or steel)
  • Alloy and temper, if known
  • Gauge and coil width
  • Coating system and color (a RAL number or a sample)
  • Quantity and destination port

Our technical office reviews every RFQ and replies with a specification and quote. We respond to RFQs within one business day.

Sourcing gutter coil?

Tell us your machine width, gauge and color, we will match the coating. Include your application, substrate (aluminum or steel), alloy, gauge, width, coating, color, quantity and destination. We respond to RFQs within one business day.

Request a Quote