About · Process

How aluminum coil is made, from scrap to finished coil.

Aluminum coil is made by melting metal, casting it, hot rolling it into thick strip and cold rolling it down to final gauge, then annealing, coating, slitting or embossing it as the order requires. This page walks through how aluminum coil is made at Orbit in Aqaba, Jordan, where recycling, casting, rolling and coating run on one integrated site.

  • Recycling and casting in Jordan
  • Hot and cold rolling
  • Coating, slitting, embossing

Where does the aluminum production process start?

With one of two sources of metal. Primary aluminum is smelted from alumina by electrolysis. Recycled aluminum is scrap that is sorted and remelted, which skips the electrolytic smelting step. Either way, the metal reaches the cast house as liquid aluminum, and from there the route to coil is the same: cast, roll, then finish.

Orbit's chain starts with recycling. Metal is melted and cast by Orbit in Jordan, so the coil's origin is the Aqaba site, and a certificate of origin is available. The diagram below shows the sequence; the sections after it explain each step.

1

Recycling

Scrap is sorted and prepared for the furnace.

2

Melting and casting

The charge is melted, adjusted to the alloy chemistry and cast.

3

Hot rolling

The cast metal is rolled at elevated temperature into thick strip.

4

Cold rolling

Further passes bring the strip to final gauge and raise its strength.

5

Annealing, where the temper needs it

Heat softens strain-hardened metal toward the ordered temper.

6

Painting on a coating line

The strip is cleaned, pretreated, primed, topcoated and cured.

7

Cutting to width and length

Master coils are slit into narrower coils or cut into sheets.

8

Embossing

Patterned rolls press a texture into the strip when the order calls for it.

How aluminum coil is made: recycling, melting and casting

Recycling

Scrap is sorted to keep the melt clean and to group material by type, because aluminum's final properties depend on its chemistry. Orbit remelts scrap on its own site. On select coated coil, for example a 3105 substrate with a PUPA coating, about 75% recycled content is achievable, confirmed per order and traceable to the cast batch. The page on Orbit's recycling loop from scrap to coil follows the metal through that loop.

Melting and the aluminum casting process

In the furnace the charge is melted and its chemistry adjusted with alloying elements to reach the target alloy, such as manganese for the 3xxx series or magnesium for the 5xxx series. Casting then turns the liquid metal into a solid form that can be rolled. Two routes are used across the industry. Most commercial alloys are cast as ingots by direct chill (DC) casting and then hot and cold rolled. Continuous casting, for example between two rolls, converts molten metal directly into coiled strip that goes on to cold rolling.

Orbit casts 1xxx, 3xxx and 5xxx alloys in Jordan. Casting is the step that fixes the chemistry, which is why the recycled-content figure and the material certificate both trace back to the cast batch.

Hot rolling vs cold rolling: what does each step do?

Hot rolling takes the thick cast metal at elevated temperature, where it is soft enough to accept heavy reductions in each pass, and rolls it into thick strip that is coiled. Cold rolling then reduces that strip to final gauge without preheating. Cold rolling hardens the metal by strain hardening, gives closer control of thickness and produces a smoother surface.

Hot rolling and cold rolling compared, qualitatively
PointHot rollingCold rolling
Metal temperatureElevatedNo preheating
Main jobLarge reductions from cast metal to thick stripReduction to final gauge
Effect on strengthMetal stays relatively softStrain hardening raises strength
Thickness control and surfaceCoarserCloser tolerances and a smoother surface

Orbit hot and cold rolls on site. Its rolled aluminum coil runs from 0.20 to 2.00 mm thick, up to 1650 mm wide, with coil weights up to 10 tonnes, in 1xxx, 3xxx and 5xxx alloys.

Annealing

Because cold rolling hardens the metal, the temper at the end of rolling depends on how much reduction it took. Annealing heats strain-hardened metal to soften it, fully to the O temper or partly to an H2x temper. Whether a coil is annealed, and how, depends on the temper ordered. The temper designations chart explains what each code means.

How is the rolled strip painted?

On a continuous coating line. The coil is unwound, cleaned and pretreated so the paint adheres, then primed, topcoated and cured in an oven before it is recoiled. Both faces can be coated, and the reverse side is specified separately from the show face. The heat of the cure can soften strain-hardened metal slightly, which is why coated coil can carry an H4x temper: strain hardened and then heated during the paint cure.

Orbit's coating systems are PE, HDPE, PVDF, PU, PUPA, Epoxy, Acrylic and Epoxy-PE, in RAL or custom colors, and 3105 is the main coated substrate. Orbit's prepainted aluminum coil is available up to 1.60 mm thick and up to 1350 mm wide. Orbit also supplies prepainted steel coil.

How is coil cut and textured for the customer?

Cutting to width and length

A master coil from the rolling or coating line is usually wider and heavier than a fabricator's machine takes. On a slitting line, rotary knives cut it lengthwise into narrower coils. On a cut-to-length line, the strip is uncoiled, flattened and sheared into sheets. Orbit's slitting and cut-to-length service covers both, with width and length set by the order.

Embossing

Embossing rolls a texture into the metal. The strip runs between an engraved roll and a second roll, either a matching engraved roll or a softer backup roll, so the pattern is part of the aluminum rather than a surface layer. Orbit's stucco embossed aluminum is supplied mill finish or coated, and the sequence of embossing and coating is settled per order.

Inspection and certificates

Orbit produces to ASTM or EN standards depending on the market and supplies material certificates with every batch. The quality system is certified to ISO 9001, with ISO 14001 for environmental management and ISO 45001 for occupational health and safety.

What does an integrated route change for the buyer?

When every step from the furnace to the finished coil runs on one site, the records do too. The cast batch, the rolled coil, the coating run and the slit coils sit in one production history, so a question about chemistry, recycled content or origin can be answered from the mill's own records rather than pieced together from several suppliers.

In practice that means three things on an order from Orbit:

  • A material certificate with every batch, to ASTM or EN depending on the market
  • Recycled content, where specified, confirmed per order and traceable to the cast batch
  • A certificate of origin for metal melted and cast in Jordan

From Aqaba, transit is about 5 to 13 days port to port to Europe and around 25 days to the USA. The minimum order is 6.5 MT, and RFQs are answered within one business day.

Process questions.

How is aluminum coil made?

Metal is melted and cast, hot rolled into thick strip and cold rolled to final gauge. It can then be annealed, coated, slit, cut to length or embossed, depending on the order.

What is the difference between hot rolling and cold rolling?

Hot rolling works the metal at elevated temperature for large reductions. Cold rolling brings it to final gauge without preheating, raising strength through strain hardening and giving closer thickness control and a smoother surface.

What casting methods are used for aluminum coil?

Most commercial alloys are cast as ingots by direct chill casting and then rolled. Continuous casting converts molten metal directly into coiled strip for cold rolling.

Why is aluminum coil annealed?

Cold rolling hardens the metal. Annealing softens it, fully to the O temper or partly to an H2x temper, so the coil meets the temper ordered.

Can recycled aluminum be made into coil?

Yes. Scrap is sorted, remelted and cast like any other charge. At Orbit, about 75% recycled content is achievable on select coated coil, confirmed per order and traceable to the cast batch.

Where is Orbit's aluminum melted and cast?

In Jordan, on Orbit's integrated site in Aqaba. A certificate of origin is available.

Need coil from one integrated mill?

Send the alloy, temper, thickness, width, finish and quantity. Material certificates come with every batch, and we respond to RFQs within one business day.

Request a Quote