Reference · Calculator
Aluminum coil calculator: weight, length, OD and PIW.
This aluminum coil calculator works out coil weight, strip length, outside diameter, PIW and flat sheet weight from the dimensions you enter, in metric or imperial units. It runs entirely in your browser, and the formula used is shown under each result.
- Five calculations
- Metric or imperial
- Alloy density presets
Coil and sheet calculator.
Result
- Coil weight
- 3,133.0 kg (6,907.0 lb)
- Strip length
- 1,856.6 m (6,091.1 ft)
Formula used: Weight (kg) = π / 4 × (OD² − ID²) × width × density / 1,000,000, with mm and g/cm³. Length (m) = π × (OD² − ID²) / (4 × thickness) / 1,000.
Results assume tightly wound bare metal with no interleaf or coating allowance. They are estimates for planning, not a substitute for the weighed coil weight on a packing list or mill certificate.
How each formula in the aluminum coil calculator works
The calculator works in millimeters, kilograms and grams per cubic centimeter. Imperial inputs are converted first, using 1 in = 25.4 mm and 1 lb = 0.45359237 kg. Where a formula multiplies millimeters by a density in g/cm³, dividing by 1,000,000 gives kilograms. The examples below use a density of 2.70 g/cm³.
Coil weight from OD, ID and width
A coil is treated as a solid ring of metal. Its weight is the area of the ring times the width times the density:
Weight (kg) = π / 4 × (OD² − ID²) × width × density / 1,000,000
OD, ID and width are in mm. If you also enter a thickness, the tab gives the strip length wound between the two diameters: Length (m) = π × (OD² − ID²) / (4 × thickness) / 1,000.
Example: OD 1200 mm, ID 508 mm, width 1250 mm. OD² − ID² = 1,440,000 − 258,064 = 1,181,936 mm². Multiplied by π / 4, by 1250 and by 2.70, then divided by 1,000,000, that is 3,133.0 kg. At 0.50 mm thickness the same coil holds 1,856.6 m of strip.
Coil length from weight, width and thickness
Coil length follows from the volume of metal, which is the weight divided by the density, spread over the strip's cross section:
Length (m) = weight × 1,000,000 / (density × width × thickness) / 1,000
Weight is in kg, width and thickness in mm.
Example: 3,000 kg, 1250 mm wide, 0.50 mm thick. Density × width × thickness = 2.70 × 1250 × 0.50 = 1,687.5. Then 3,000 × 1,000,000 / 1,687.5 / 1,000 = 1,777.8 m. The step-by-step coil weight and length walk-through works a longer example with the unit conversions written out.
Coil OD from weight, ID and width
This is the weight formula solved for the outside diameter:
OD (mm) = √(ID² + 4 × weight × 1,000,000 / (π × density × width))
Weight is in kg, ID and width in mm. It is useful for checking a coil of a given weight against an OD limit on the receiving equipment.
Example: 3,000 kg, ID 508 mm, width 1250 mm. The second term is 4 × 3,000,000,000 / (π × 2.70 × 1250) = 1,131,768, and ID² is 258,064. The square root of 1,389,832 is 1,178.9 mm, so the coil OD is about 1,179 mm.
PIW and kg per mm of width
PIW is pounds per inch of width: the coil weight divided by the strip width. It states how much weight sits on each unit of width, so coils of different widths can be compared on the same basis.
PIW = weight in lb / width in inches. Metric equivalent: kg per mm of width = weight in kg / width in mm.
PIW does not depend on density.
Example: 3,000 kg on 1250 mm width is 2.40 kg per mm of width. In imperial terms that is 6,613.9 lb on 49.21 in, or 134.4 lb per inch of width.
Sheet weight
The aluminum sheet weight calculator tab multiplies the sheet volume by the density and the number of sheets:
Weight (kg) = length × width × thickness × density × quantity / 1,000,000
Length, width and thickness are in mm.
Example: a 2500 × 1250 × 1.0 mm sheet weighs 2500 × 1250 × 1.0 × 2.70 / 1,000,000 = 8.4375 kg, shown as 8.44 kg. One hundred sheets weigh 843.75 kg.
Density values used
Density is the only material property in these formulas. It changes every weight-based result; PIW and the strip length from diameters do not depend on it. The calculator offers these presets, and accepts a custom value.
| Material | g/cm³ | lb/in³ |
|---|---|---|
| Aluminum, general | 2.70 | 0.0975 |
| 1100 (1xxx series) | 2.71 | 0.0979 |
| 3003 (3xxx series) | 2.73 | 0.0986 |
| 3105 (3xxx series) | 2.72 | 0.0983 |
| 5052 (5xxx series) | 2.68 | 0.0968 |
| Carbon steel | 7.85 | 0.2836 |
Source: aluminum values are typical nominal densities for these alloys; for an exact figure, use the value on the alloy data sheet or mill certificate. 7.85 g/cm³ is the conventional value for carbon steel.
What the calculator assumes
Results are planning estimates. The formulas assume:
- Solid wraps: each wrap sits tight on the one below, with no air gap.
- No interleaf: no paper or film between wraps.
- Bare metal: no allowance for paint, primer or protective film weight.
- Nominal thickness: the thickness you enter, not the actual thickness within its tolerance.
Real coils can run slightly larger in diameter than the formula gives for the same weight, because of air between wraps and any interleaf. The weight that counts for a shipment is the weighed weight on the packing list and the mill certificate.
Inside diameter. The coil ID is set by the mandrel the mill winds on and the uncoiler the buyer runs, so ask the mill which IDs it can supply for your line. The 508 mm in the calculator is only an example value.
Orbit coil sizes. Orbit supplies rolled aluminum coil from 0.20 to 2.00 mm thick, up to 1650 mm wide and in coils up to 10 tonnes. Coils can be slit to narrower widths or cut into sheet through slitting and cut-to-length. If your drawing gives thickness as a gauge number, convert it with the aluminum and steel gauge table before using it here.
Coil calculator questions.
How do you calculate the weight of an aluminum coil?
Take the outside diameter squared minus the inside diameter squared, multiply by pi divided by four, then multiply by the width and the density. With dimensions in mm and density in grams per cubic centimeter, divide by one million to get kilograms. A coil with a 1200 mm OD, 508 mm ID and 1250 mm width at a density of 2.70 weighs about 3,133 kg.
What does PIW mean?
PIW means pounds per inch of width. It is the coil weight in pounds divided by the strip width in inches. The metric equivalent is kilograms per millimeter of width. A 3,000 kg coil 1250 mm wide is 134.4 PIW, or 2.40 kg per mm.
Can the calculator give strip length from coil weight?
Yes. It divides the weight by the density times the width times the thickness, then converts to meters. A 3,000 kg aluminum coil 1250 mm wide and 0.50 mm thick at a density of 2.70 holds about 1,778 m of strip.
Why is the actual coil weight different from the calculated weight?
The calculator assumes tight wraps with no air gap, no interleaf, no coating and exactly the nominal thickness. Real coils differ slightly on each point, so use the weighed weight on the packing list.
Which density should I use for aluminum?
Use the alloy's nominal density if you know it: 2.71 for 1100, 2.73 for 3003, 2.72 for 3105 and 2.68 for 5052, in grams per cubic centimeter. If the alloy is not known, 2.70 is a reasonable general value for aluminum.
What inside diameter should I enter?
Enter the ID of the coil you are ordering or receiving. The ID depends on the mill's winding mandrel and the buyer's uncoiler, so confirm it with the mill. The default of 508 mm is only an example.
Ready to size an order?
Send the alloy, temper, thickness, width, coil weight or OD limit, inside diameter, finish, quantity and destination. We respond to RFQs within one business day.
