Reference · Thickness
Sheet metal gauge chart for aluminum and steel.
This sheet metal gauge chart gives the thickness of each gauge number in inches and millimeters for aluminum, uncoated steel and galvanized steel. Aluminum and steel use different gauge systems, so the same gauge number means a different thickness in each metal: read the table for the metal you are buying.
- Gauges 8 to 30
- Inches and mm
- Aluminum, steel and galvanized
Sheet metal gauge chart: why aluminum and steel differ
A gauge number is not a thickness on its own. It points to a row in a table, and aluminum and steel have different tables. Aluminum sheet gauge numbers, where they are used, follow the Brown & Sharpe system, and many mills quote aluminum sheet by decimal thickness instead. Uncoated steel sheet is gauged on the Manufacturers' Standard Gauge, and galvanized steel on its own galvanized sheet gauge.
The gap is large enough to matter on an order. At 16 gauge:
- 16 gauge aluminum: 0.0508 in (1.290 mm)
- 16 gauge steel: 0.0598 in (1.519 mm)
- 16 gauge galvanized steel: 0.0635 in (1.613 mm)
A buyer who reads a steel table for an aluminum order would expect metal about 0.23 mm thicker than the aluminum gauge actually describes. The tables below list each system separately, and the converter between them looks up any gauge in all three.
Aluminum sheet gauge chart (Brown & Sharpe)
Aluminum gauge thickness, where a gauge is used, follows the Brown & Sharpe series, the same series as American Wire Gauge (AWG). Each step down in gauge number makes the metal thicker by the same ratio, so the series is geometric. The last column shows where each thickness sits against Orbit's rolled and coated ranges.
| Gauge | Inches | mm | Relative thickness | Orbit range |
|---|---|---|---|---|
| 8 | 0.1285 | 3.264 | Outside range | |
| 9 | 0.1144 | 2.906 | Outside range | |
| 10 | 0.1019 | 2.588 | Outside range | |
| 11 | 0.0907 | 2.304 | Outside range | |
| 12 | 0.0808 | 2.052 | Outside range | |
| 13 | 0.0720 | 1.829 | Rolled only | |
| 14 | 0.0641 | 1.628 | Rolled only | |
| 15 | 0.0571 | 1.450 | Rolled and coated | |
| 16 | 0.0508 | 1.290 | Rolled and coated | |
| 17 | 0.0453 | 1.151 | Rolled and coated | |
| 18 | 0.0403 | 1.024 | Rolled and coated | |
| 19 | 0.0359 | 0.912 | Rolled and coated | |
| 20 | 0.0320 | 0.813 | Rolled and coated | |
| 21 | 0.0285 | 0.724 | Rolled and coated | |
| 22 | 0.0253 | 0.643 | Rolled and coated | |
| 23 | 0.0226 | 0.574 | Rolled and coated | |
| 24 | 0.0201 | 0.511 | Rolled and coated | |
| 25 | 0.0179 | 0.455 | Rolled and coated | |
| 26 | 0.0159 | 0.404 | Rolled and coated | |
| 27 | 0.0142 | 0.361 | Rolled and coated | |
| 28 | 0.0126 | 0.320 | Rolled and coated | |
| 29 | 0.0113 | 0.287 | Rolled and coated | |
| 30 | 0.0100 | 0.254 | Rolled and coated |
Key to the Orbit range column. "Rolled and coated" means the thickness is inside Orbit's rolled range of 0.20 to 2.00 mm and at or below the 1.60 mm coated maximum. "Rolled only" means it is inside the rolled range but above the coated maximum. "Outside range" means it falls outside the rolled range.
Source: the Brown & Sharpe series is the American Wire Gauge series, whose sizes are defined by the equations in ASTM B258; using it for sheet thickness is trade convention. Values here are the series values rounded to four decimals in inches, with millimeters converted at 25.4 mm per inch.
Gauge to mm converter.
Result
- 16 gauge aluminum
- 0.0508 in = 1.290 mm
- Orbit range
- Inside Orbit’s rolled range (0.20 to 2.00 mm) and coated range (up to 1.60 mm).
- Nearest gauge to 1.00 mm
- Aluminum: 18 gauge (1.024 mm). Steel: 19 gauge (1.062 mm). Galvanized steel: 20 gauge (1.006 mm).
How it works: the converter reads the same tables printed on this page. Aluminum uses Brown & Sharpe, steel uses the Manufacturers’ Standard Gauge, galvanized steel uses the galvanized sheet gauge.
Steel and galvanized steel gauge thickness
The steel column is the Manufacturers' Standard Gauge for uncoated sheet steel. The galvanized column is the galvanized sheet gauge. At the same gauge number, galvanized sheet is thicker than uncoated steel because its figure includes the zinc coating. The last column repeats the aluminum value from the table above for comparison.
All gauge numbers in these tables are nominal. Steel producers recommend ordering sheet by decimal thickness, and gauge numbers survive as a reference, so use this table for orientation and the governing standard for acceptance.
| Gauge | Steel (in) | Steel (mm) | Galvanized (in) | Galvanized (mm) | Aluminum (mm) |
|---|---|---|---|---|---|
| 8 | 0.1644 | 4.176 | 0.1681 | 4.270 | 3.264 |
| 9 | 0.1495 | 3.797 | 0.1532 | 3.891 | 2.906 |
| 10 | 0.1345 | 3.416 | 0.1382 | 3.510 | 2.588 |
| 11 | 0.1196 | 3.038 | 0.1233 | 3.132 | 2.304 |
| 12 | 0.1046 | 2.657 | 0.1084 | 2.753 | 2.052 |
| 13 | 0.0897 | 2.278 | 0.0934 | 2.372 | 1.829 |
| 14 | 0.0747 | 1.897 | 0.0785 | 1.994 | 1.628 |
| 15 | 0.0673 | 1.709 | 0.0710 | 1.803 | 1.450 |
| 16 | 0.0598 | 1.519 | 0.0635 | 1.613 | 1.290 |
| 17 | 0.0538 | 1.367 | 0.0575 | 1.461 | 1.151 |
| 18 | 0.0478 | 1.214 | 0.0516 | 1.311 | 1.024 |
| 19 | 0.0418 | 1.062 | 0.0456 | 1.158 | 0.912 |
| 20 | 0.0359 | 0.912 | 0.0396 | 1.006 | 0.813 |
| 21 | 0.0329 | 0.836 | 0.0366 | 0.930 | 0.724 |
| 22 | 0.0299 | 0.759 | 0.0336 | 0.853 | 0.643 |
| 23 | 0.0269 | 0.683 | 0.0306 | 0.777 | 0.574 |
| 24 | 0.0239 | 0.607 | 0.0276 | 0.701 | 0.511 |
| 25 | 0.0209 | 0.531 | 0.0247 | 0.627 | 0.455 |
| 26 | 0.0179 | 0.455 | 0.0217 | 0.551 | 0.404 |
| 27 | 0.0164 | 0.417 | 0.0202 | 0.513 | 0.361 |
| 28 | 0.0149 | 0.378 | 0.0187 | 0.475 | 0.320 |
| 29 | 0.0135 | 0.343 | 0.0172 | 0.437 | 0.287 |
| 30 | 0.0120 | 0.305 | 0.0157 | 0.399 | 0.254 |
Source: steel columns: Manufacturers' Standard Gauge, nominal values (based on 41.82 lb per square foot per inch of thickness). Galvanized columns: Galvanized sheet gauge, nominal values (including the zinc coating). Aluminum column: the Brown & Sharpe values from the table above.
Why gauge numbers differ between metals
The gauge systems grew up separately, for different trades, and were never meant to agree with each other.
The Brown & Sharpe gauge is a geometric series. Gauge 0000 is 0.4600 in and gauge 36 is 0.0050 in, a ratio of 92, and the 39 steps between them divide that ratio evenly. It was set up for nonferrous metal and wire, which is why aluminum and other nonferrous sheet gauge numbers, where used, still follow it and why it matches American Wire Gauge.
The sheet steel gauge took a different starting point: weight per unit area. Each gauge number stood for a set weight of steel per square foot, and the thickness was worked out from that weight. Because the conversion runs through the density of steel, the thickness values only make sense for steel. Apply them to aluminum, which is roughly a third as dense, and the weight basis no longer holds.
Neither system is a unit of measure. A gauge number is a label for a nominal thickness inside one particular table. Thickness itself is measured in millimeters or inches. Other systems, such as the British Standard Wire Gauge and the Birmingham Wire Gauge, assign different thicknesses again, so a drawing should name the system or, better, give the decimal thickness.
Order by mm, not gauge
Mills roll aluminum sheet metal to a decimal thickness and certify it against a tolerance. The mill certificate states the thickness in millimeters or inches, and the inspection on receipt measures the same thing. An aluminum sheet metal gauge number carries no tolerance of its own, and it can be read against the wrong table: a supplier working from a steel chart and a buyer working from an aluminum chart can both quote "18 gauge" and mean sheet about 0.19 mm apart.
To avoid that, state on the purchase order:
- The thickness in mm or decimal inches, for example 1.00 mm or 0.040 in.
- The tolerance standard that applies, for example ANSI H35.2 (dimensional tolerances for US aluminum sheet and plate) or EN 485-4 for aluminum sheet, depending on your market.
- The alloy and temper, because they decide formability and strength at a given thickness.
- For painted coil, whether the thickness is for the bare metal or includes the paint film.
If a drawing gives only a gauge, convert it once with the table above, write the decimal value on the order, and keep the gauge as a reference note only. Orbit quotes rolled aluminum coil from 0.20 to 2.00 mm and prepainted coil in thicknesses up to 1.60 mm, both stated in millimeters. To turn a thickness into a coil weight or strip length, use the coil weight and length calculator.
Common aluminum sheet gauges
The five gauges below, with the aluminum value from the Brown & Sharpe table and the steel value at the same number for contrast.
14 gauge aluminum sheet
14 gauge aluminum sheet is 0.0641 in, or 1.628 mm. 14 gauge steel is 0.0747 in (1.897 mm). At 1.628 mm it is inside Orbit's rolled range but above the 1.60 mm coated maximum, so it is rolled only.
16 gauge aluminum sheet
16 gauge aluminum sheet is 0.0508 in, or 1.290 mm. 16 gauge steel is 0.0598 in (1.519 mm). It falls inside both Orbit's rolled and coated ranges.
18 gauge aluminum sheet
18 gauge aluminum sheet is 0.0403 in, or 1.024 mm. 18 gauge steel is 0.0478 in (1.214 mm). It is inside Orbit's rolled and coated ranges.
20 gauge aluminum sheet
20 gauge aluminum sheet is 0.0320 in, or 0.813 mm. 20 gauge steel is 0.0359 in (0.912 mm). It is inside Orbit's rolled and coated ranges.
22 gauge aluminum sheet
22 gauge aluminum sheet is 0.0253 in, or 0.643 mm. 22 gauge steel is 0.0299 in (0.759 mm). It is inside Orbit's rolled and coated ranges.
Which gauge suits a part depends on the alloy, temper, span, fastening and forming method, so this page does not recommend a gauge for a product. For one application with its own conventions, the gutter coil gauge, alloy and coating guide covers how gutter coil thickness is specified.
Gauge thickness questions.
Is aluminum gauge the same as steel gauge?
No. Aluminum sheet gauge numbers, where they are used, follow the Brown and Sharpe gauge, while uncoated steel uses the Manufacturers' Standard Gauge and galvanized steel its own galvanized sheet gauge. At the same number, aluminum is thinner: 16 gauge aluminum is 1.290 mm, 16 gauge steel is 1.519 mm and 16 gauge galvanized is 1.613 mm.
How thick is 16 gauge aluminum sheet?
16 gauge aluminum sheet is 0.0508 inches, which is 1.290 mm, on the Brown and Sharpe gauge.
Does a higher gauge number mean thicker metal?
No. In every sheet gauge system on this page, a higher gauge number means thinner metal. 30 gauge aluminum is 0.254 mm, while 8 gauge aluminum is 3.264 mm.
Why is galvanized steel thicker than plain steel at the same gauge?
The galvanized sheet gauge includes the zinc coating in its thickness figure, so at the same gauge number the galvanized value is greater than the uncoated steel value.
Is the Brown and Sharpe gauge the same as American Wire Gauge?
Yes. Brown and Sharpe and American Wire Gauge are the same series, whose sizes are defined by the equations in ASTM B258. Using it for aluminum and other nonferrous sheet thickness, as well as wire, is trade convention.
Should I order aluminum sheet by gauge or by thickness?
By thickness. State the thickness in mm or decimal inches together with the tolerance standard, such as ANSI H35.2 (dimensional tolerances for US aluminum sheet and plate) or EN 485-4. A gauge number carries no tolerance and can be read against the wrong table.
Which aluminum gauges does Orbit supply?
Orbit rolls aluminum from 0.20 to 2.00 mm and coats up to 1.60 mm, and quotes in millimeters. Of the Brown and Sharpe gauges in this chart, 13 to 30 fall inside the rolled range and 15 to 30 inside the coated range.
Have a thickness to quote?
Send the thickness in mm or inches, the tolerance standard, alloy, temper, width, finish, quantity and destination. We respond to RFQs within one business day.
