Reference · Standards
EN 10204 3.1: the inspection certificate explained.
An EN 10204 3.1 document is an inspection certificate based on specific inspection of the products supplied, issued by the manufacturer and validated by an authorized inspection representative who is independent of the manufacturing department. It is one of four document types in EN 10204:2004. This page compares types 2.1, 2.2, 3.1 and 3.2 and explains what to write on a coil order.
- Types 2.1, 2.2, 3.1 and 3.2
- Specific vs non-specific inspection
- What to state on the order
What is an EN 10204 3.1 certificate?
EN 10204 defines the types of inspection document a supplier of metallic products can give a buyer. It does not set any property limits itself. Those come from the product standard on the order, such as EN 485 or ASTM B209. What EN 10204 settles is the kind of evidence: whether the document only declares compliance, whether it reports test results, whether those results come from the lot you receive, and who signs it.
A 3.1 certificate combines two things a buyer of flat-rolled aluminum usually wants: test results from specific inspection of the delivered products, and validation by someone at the manufacturer who is independent of the manufacturing department. It does not require an outside inspector. That is the difference from type 3.2.
EN 10204 3.1 compared with types 2.1, 2.2 and 3.2
The four types fall into two groups. Types 2.1 and 2.2 are based on non-specific inspection. Types 3.1 and 3.2 are based on specific inspection.
| Type | Name | Who issues and validates it | What it contains | Basis |
|---|---|---|---|---|
| 2.1 | Declaration of compliance with the order | The manufacturer | A statement that the products comply with the order, with no test results | Non-specific inspection |
| 2.2 | Test report | The manufacturer | A statement of compliance with the order, with test results from non-specific inspection | Non-specific inspection |
| 3.1 | Inspection certificate 3.1 | The manufacturer, validated by its authorized inspection representative, independent of the manufacturing department | A statement of compliance with the order, with test results from specific inspection | Specific inspection |
| 3.2 | Inspection certificate 3.2 | As 3.1, and also validated by the purchaser's authorized representative or an inspector named in official regulations | A statement of compliance with the order, with test results from specific inspection | Specific inspection |
Specific and non-specific inspection
Specific inspection is carried out before delivery on the products to be supplied, or on test units that include them. Non-specific inspection is the manufacturer's own inspection of products made by the same process, which need not be the products you receive. A 2.2 test report can therefore show typical results for the product, while a 3.1 certificate shows results for the lot on your order.
What happened to 3.1.A, 3.1.B and 3.1.C?
The 2004 edition of EN 10204 replaced the earlier 3.1.A, 3.1.B and 3.1.C types. Old specifications sometimes still call for "3.1.B". If yours does, update it to a current type before you send the RFQ.
What should a coil order say about the certificate?
"Certificate required" on a purchase order leaves too much open. Three things make the requirement specific:
- The document type. Write it out in full, for example "inspection certificate EN 10204 type 3.1". If you need type 3.2, say who will validate it for your side, so it can be agreed when the order is placed.
- Which properties it must report. For flat-rolled aluminum this is usually the chemical composition of the cast and the mechanical properties for the alloy and temper ordered (tensile strength, yield strength and elongation), with dimensions. If you need anything beyond what the product standard requires, list it.
- The lot or cast reference. Ask for the cast or batch number and the coil numbers to appear on the certificate, so the paper can be tied to the coil tags on arrival.
The certificate also needs a product standard to report against. Name it on the same order, with the alloy and temper in that standard's designation system. For EN orders, the EN 485 and EN 573 standards supply the property and composition limits; for ASTM orders, see how ASTM B209 sets them.
For coated coil, keep the metal and the paint apart: the certificate requirement for the aluminum is one line, and any coating test results you want reported are another, naming the test methods.
How does a 3.1 certificate relate to a mill test report?
"Mill test report", "mill test certificate" and "material certificate" are trade names, used loosely and often for the same document. They describe what the paper looks like: the standard, alloy and temper, measured composition, mechanical test results and the lot reference. EN 10204 describes what kind of evidence the paper is. A mill test report can be issued as a 3.1 certificate, but the name alone does not tell you that; the document should state its EN 10204 type.
When a certificate arrives, check that it states the type you ordered, that the standard and the alloy and temper match the purchase order, that each reported result sits inside the limits of that standard, and that the cast and coil numbers match the coils received. Our guide to reading the mill test report line by line walks through each field.
Certificates on Orbit coil orders
Orbit supplies to ASTM or EN standards depending on the market, with material certificates with every batch. State the document type you need in the RFQ and Orbit will confirm what it can issue. The relevant facts:
- Integrated aluminum coil manufacturer in Aqaba, Jordan, family owned and operating since 1976.
- Metal melted and cast by Orbit in Jordan. Certificate of origin available.
- Rolled aluminum coil in the 1xxx, 3xxx and 5xxx series, with coil coating, slitting and cut-to-length in house.
- ISO 9001, ISO 14001 and ISO 45001 certified.
Standards referenced
- EN 10204:2004, metallic products, types of inspection documents
- EN 485, aluminum sheet, strip and plate (parts 1 to 4)
- EN 573, chemical composition and form of wrought products
- ASTM B209/B209M, Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
EN 10204 questions.
What does EN 10204 3.1 mean?
It is an inspection certificate based on specific inspection of the products supplied, with test results, issued by the manufacturer and validated by its authorized inspection representative who is independent of the manufacturing department.
What is the difference between a 2.2 and a 3.1 certificate?
A 2.2 test report gives results from non-specific inspection, which need not come from the products delivered. A 3.1 certificate gives results from specific inspection of the products supplied and is validated by an inspection representative independent of manufacturing.
What is the difference between 3.1 and 3.2?
A 3.2 certificate is also validated by the purchaser's authorized representative or by an inspector named in official regulations. A 3.1 certificate is validated within the manufacturer only.
Is 3.1.B still valid?
The 2004 edition of EN 10204 replaced the 3.1.A, 3.1.B and 3.1.C types. If an old specification calls for 3.1.B, agree the current document type with the supplier before ordering.
Is a mill test report the same as an EN 10204 3.1 certificate?
Not necessarily. Mill test report is a trade name. It can be issued as a 3.1 certificate, but the document should state its EN 10204 type, and that type should match the order.
Which EN 10204 type does Orbit issue?
Orbit supplies material certificates with every batch. State the document type you need in the RFQ and Orbit will confirm what it can issue for your order.
Need a certificate with your coil?
Send the standard, alloy, temper, thickness, width, document type, quantity and destination. We respond to RFQs within one business day.
