Reference · Standards
EN 485, EN 573 and EN 1396 for aluminum coil.
EN 485 is the European standard for aluminum sheet, strip and plate: four parts covering inspection and delivery, mechanical properties and dimensional tolerances. It works with EN 573 for alloy designation and composition, EN 515 for tempers and, on painted material, EN 1396 for coil coated sheet and strip. This page explains what each standard covers and how they appear together on an order.
- EN 485 parts 1 to 4
- EN 573 parts 1 to 3
- EN 1396 coil coated sheet and strip
What does EN 485 cover?
EN 485 is a product standard for flat-rolled aluminum and aluminum alloys. It sets what the delivered sheet, strip or plate must meet, and it is split into four parts, each with its own job. It does not define the alloys or tempers itself: composition comes from EN 573-3 and temper designations from EN 515. A buyer ordering to EN 485 is therefore relying on at least three standards at once, even if only one is named on the order.
| Part | Title | What it controls |
|---|---|---|
| EN 485-1 | Technical conditions for inspection and delivery | The conditions under which the product is inspected and delivered |
| EN 485-2 | Mechanical properties | Tensile strength, yield strength and elongation limits by alloy, temper and thickness |
| EN 485-3 | Tolerances on dimensions and form for hot-rolled products | Permitted variation in the dimensions and form of hot-rolled products |
| EN 485-4 | Tolerances on shape and dimensions for cold-rolled products | The same for cold-rolled products, over 0.20 mm up to and including 50 mm thick. Thinner material is classed as foil under EN 546. |
For coil, the parts that matter most in day-to-day buying are usually EN 485-2, because it decides whether the mechanical test results on the certificate pass, and the tolerance part that matches the rolling route. Bend limits depend on alloy, temper and thickness. EN 485-2 sets the mechanical property limits; ask for bend data per order.
What does EN 573 define?
EN 573 is the European designation and composition standard for wrought aluminum. Its first three parts are the ones a coil buyer meets:
- EN 573-1, "Chemical composition and form of wrought products. Numerical designation system". This gives each alloy its four-digit designation, written with the prefix EN AW, as in EN AW-3105.
- EN 573-2, "Chemical symbol based designation system". This gives an alternative name built from the chemical symbols of the main alloying elements, as in EN AW-5754 [AlMg3].
- EN 573-3, "Chemical composition and form of products". This sets the composition limits for each alloy, and it is the part EN 485 refers to for composition.
On an EN order, the alloy is named with its EN AW designation and the measured composition on the certificate is checked against EN 573-3. The rolled coil Orbit produces is in the 1xxx, 3xxx and 5xxx series.
What does EN 1396 cover?
EN 1396 is titled "Coil coated sheet and strip for general applications. Specifications"; the current edition is from 2023. It covers aluminum sheet and strip that has been coil coated for general use, with liquid or powder paint. Can stock is outside its scope.
EN 1396 sits on top of the metal standards rather than replacing them. The substrate is still aluminum sheet or strip with an alloy, a temper and dimensions, so the EN 573 and EN 515 designations still describe the metal under the paint. EN 1396 adds the requirements that belong to coated material. For prepainted aluminum coil ordered to EN, it is the standard that ties the paint and the substrate into one specification. Coating test methods themselves, such as film thickness, gloss and T-bend, are set out in the EN 13523 series.
How do EN 485, EN 573 and EN 1396 appear on an order?
An EN order for bare coil names the product standard, then the alloy and temper, then the size and finish. In general form:
| Field | Example entry | Governed by |
|---|---|---|
| Product standard | EN 485, or EN 1396 for coil coated material | EN 485-1 to -4 for uncoated sheet and strip; EN 1396 for coated coil |
| Alloy | EN AW-[four-digit alloy] | EN 573-1, composition per EN 573-3 |
| Temper | [temper code] | EN 515, property limits per EN 485-2 |
| Thickness and width | [thickness] x [width] mm | EN 485-3 or EN 485-4 tolerances |
| Finish | Mill finish, or coil coated | EN 1396 if coil coated |
| Coating | [paint system, color, gloss, film thickness] | EN 1396; test methods per EN 13523 |
| Inspection document | [type], for example 3.1 | EN 10204 |
The bracketed fields are what you fill in. Which tempers, thicknesses and coatings a given supplier can deliver is confirmed per order; the standards define what the codes mean, not what any one mill offers. Where an edition matters to your contract, add the year after the standard number.
How do the EN standards relate to ASTM B209 and EN 10204?
ASTM B209 covers the same ground as EN 485 for the North American system, but it keeps most requirements in one specification, with alloy and temper designations under ANSI H35.1. US dimensional tolerances are set in ANSI H35.2. EN 485 splits the work into parts and refers to EN 573-3 and EN 515. The two systems were written separately and are not interchangeable, so name one on the order. The ASTM B209 sheet and plate specification page compares them requirement by requirement.
EN 10204 is a different kind of standard. It does not set any property limits; it defines the types of inspection document that report conformity with the product standard. An EN 485 order with no document type leaves open whether you receive test results for your lot at all. See what an EN 10204 3.1 inspection certificate contains before you write that line.
Ordering to EN standards from Orbit
Orbit supplies to ASTM or EN standards depending on the market, with material certificates with every batch. Name the standard, alloy, temper, size, finish and document type on the RFQ. The relevant facts:
- Integrated aluminum coil manufacturer in Aqaba, Jordan, family owned and operating since 1976.
- Aluminum recycling, casting, hot and cold rolling, coil coating, slitting, cut-to-length and embossing.
- Alloys in the 1xxx, 3xxx and 5xxx series; 3105 is the main coated substrate.
- Coating systems PE, HDPE, PVDF, PU, PUPA, Epoxy, Acrylic and Epoxy-PE.
- ISO 9001, ISO 14001 and ISO 45001 certified. MOQ 6.5 MT.
Standards referenced
- EN 485-1, technical conditions for inspection and delivery
- EN 485-2, mechanical properties
- EN 485-3, tolerances on dimensions and form for hot-rolled products
- EN 485-4, tolerances on shape and dimensions for cold-rolled products
- EN 573-1, numerical designation system
- EN 573-2, chemical symbol based designation system
- EN 573-3, chemical composition and form of products
- EN 515, temper designations
- EN 1396:2023, coil coated sheet and strip for general applications
- EN 13523 series, test methods for coil coated metals
- EN 10204:2004, types of inspection documents
- ASTM B209/B209M, Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
- ANSI H35.1 and ANSI H35.2, alloy and temper designations and dimensional tolerances
EN standards questions.
What is EN 485?
EN 485 is the European standard for aluminum and aluminum-alloy sheet, strip and plate. Part 1 covers inspection and delivery, part 2 mechanical properties, part 3 tolerances for hot-rolled products and part 4 tolerances for cold-rolled products.
Where does EN 485 get its alloy compositions from?
From EN 573-3, which sets the composition limits for each alloy. Temper designations come from EN 515.
What is the difference between EN 573-1 and EN 573-2?
EN 573-1 is the numerical designation system, such as EN AW-3105. EN 573-2 is the chemical symbol based system, which names the alloy from its main alloying elements. Both can describe the same alloy.
Does EN 1396 replace EN 485 for painted coil?
For coil coated material, EN 1396 is the product standard: it covers coil coated sheet and strip for general applications. The aluminum underneath is still described by its alloy (EN 573-3) and temper (EN 515), so the metal and coating requirements are read together. EN 485 applies to uncoated sheet, strip and plate.
Is EN 485 equivalent to ASTM B209?
Both cover flat-rolled aluminum, but they are separate systems and are not interchangeable. A certificate is issued against the standard named on the order, so name one.
Can Orbit supply coil to EN standards?
Orbit supplies to ASTM or EN standards depending on the market, with material certificates with every batch. State the standard, alloy, temper and document type on the RFQ.
Ordering coil to EN?
Send the standard, alloy, temper, thickness, width, finish, document type, quantity and destination. We respond to RFQs within one business day.
