Reference · Standards
AAMA 2603 vs 2604 vs 2605: coating specifications compared.
AAMA 2603, AAMA 2604 and AAMA 2605 are three voluntary specifications, published by FGIA, that set test procedures and performance requirements for organic coatings on aluminum extrusions and panels for architectural products. They differ in the class of coating they cover: pigmented, high performance and superior performing. This page explains what each covers, the coil coating appendix and how to cite one on an order.
- Voluntary specifications
- Published by FGIA
- 2026 editions active
What are AAMA 2603, 2604 and 2605?
The three documents belong to one family. Each is a voluntary specification: it applies to a project or a purchase only when a specification, drawing or order calls for it by name. Each sets out the tests a coating is put through and the results it has to reach, for organic coatings applied to aluminum extrusions and panels for architectural products.
The documents were developed under the AAMA name and are now published by FGIA, the Fenestration and Glazing Industry Alliance. The AAMA designations are kept, so specifications still refer to them as AAMA 2603, AAMA 2604 and AAMA 2605.
AAMA 2603 vs 2604 vs 2605 side by side
The titles of the three 2026 editions follow the same form and differ in the class of coating named. The table shows the current designations and what each covers.
| Designation | Coating class in the title | Scope |
|---|---|---|
| AAMA 2603-26 | Pigmented organic coatings | Test procedures and performance requirements for pigmented organic coatings on aluminum extrusions and panels for architectural products |
| AAMA 2604-26 | High performance organic coatings | Test procedures and performance requirements for high performance organic coatings on aluminum extrusions and panels for architectural products |
| AAMA 2605-26 | Superior performing organic coatings | Test procedures and performance requirements for superior performing organic coatings on aluminum extrusions and panels for architectural products |
The full title of the first is AAMA 2603-26, Voluntary Specification, Performance Requirements and Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and Panels (with Coil Coating Appendix). AAMA 2604-26 and AAMA 2605-26 use the same wording with "High Performance" and "Superior Performing" in place of "Pigmented".
The names describe three performance classes, from pigmented through high performance to superior performing. The exposure periods, test durations and retention limits that separate the classes are set in the documents themselves, and this page does not restate them. Read them from the edition your project names, bought from FGIA.
What does the coil coating appendix cover?
All three documents carry a coil coating appendix in their titles, in the 2026 editions and in the earlier editions still listed by FGIA. Coil coating paints flat strip before it is formed into a product, which is a different process from painting a finished extrusion or panel. The appendix describes where the test procedures and performance requirements differ when the coating is applied on a coil line to aluminum for architectural products. For coil-coated panel stock, this is the part of the document to read alongside the main requirements.
FGIA lists the -26 editions as the active editions. Earlier editions are still listed on the FGIA store; cite the edition your specification names. If a project specification gives no edition, agree one with the supplier before ordering, because the test requirements and the coil appendix depend on the edition.
How to cite AAMA 2605, 2604 or 2603 on an order
A reference to AAMA 2605 on a drawing only works if both sides read it the same way. A clear citation and the evidence behind it usually cover these points:
- Name the document and edition. Write the full designation, for example AAMA 2605-26, not "AAMA 2605" or "AAMA spec" alone.
- Name the coating system and color. Performance is tested on a specific coating system in a specific color, so the citation should be tied to the system and color being ordered.
- Ask for the test reports. Request the coater's test reports for that coating system and color against the edition cited, and check that they cover the coil coating appendix where the material is coil coated.
- Keep the warranty separate. A specification sets test requirements; a coating warranty is a commercial term agreed with the supplier for an application and environment. Ask for both in writing.
Laboratory tests in coating reports are useful for comparing systems, but each test measures one thing under set conditions. The guide to the salt spray test for coated aluminum explains what one common accelerated test does and does not tell you.
Coating systems and AAMA specifications
An AAMA specification is a set of tests, not a type of paint. Whether a given coating meets one depends on the resin system, the pigments, the film build, the pretreatment and the application, and it is shown by test reports for that system and color, not by the name of the resin. When you compare options, ask which specification and edition each system has been tested against, and for which colors.
The overview of coil coating systems at Orbit sets out the systems Orbit applies: PE, HDPE, PVDF, PU, PUPA, Epoxy, Acrylic and Epoxy-PE, in solid, metallic, woodgrain and other finishes, with RAL or custom color matching. For exterior architectural work, the page on PVDF coated aluminum covers one system often specified for this kind of work. Orbit supplies prepainted aluminum coil up to 1.60 mm thick and up to 1350 mm wide, with 3105 as the main coated substrate. Test reports for a coating system and color are available on request where they exist for that system; state the specification and edition your project cites in the RFQ. Coating warranties run 5 to 20 years depending on application and environment, confirmed per order.
Standards referenced
- FGIA: AAMA 2603-26, Voluntary Specification, Performance Requirements and Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and Panels (with Coil Coating Appendix)
- FGIA: AAMA 2604-26, Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings on Aluminum Extrusions and Panels (with Coil Coating Appendix)
- FGIA: AAMA 2605-26, Voluntary Specification, Performance Requirements and Test Procedures for Superior Performing Organic Coatings on Aluminum Extrusions and Panels (with Coil Coating Appendix)
AAMA specification questions.
What is the difference between AAMA 2603, 2604 and 2605?
They cover three classes of organic coating on aluminum extrusions and panels for architectural products: pigmented (2603), high performance (2604) and superior performing (2605). Each sets its own test procedures and performance requirements, which are in the documents published by FGIA.
Who publishes AAMA 2605?
FGIA, the Fenestration and Glazing Industry Alliance. The documents keep their AAMA designations and are sold on the FGIA store.
What is the current edition of AAMA 2605?
FGIA lists AAMA 2605-26 as the active edition. Earlier editions are still listed on the FGIA store, so cite the edition your specification names.
Do the AAMA specifications cover coil coated aluminum?
Each of the three documents includes an appendix describing where test procedures and performance requirements differ for coatings applied on a coil coating line to aluminum architectural products.
Is AAMA 2605 a type of paint?
No. It is a specification of tests and performance requirements. Whether a coating meets it is shown by test reports for the specific coating system and color, against the edition cited.
Specifying coated coil for architectural work?
Send the coating system, color, specification and edition, thickness, width, quantity and destination. We respond to RFQs within one business day.
