Reference · Physical properties
Density of aluminum: values by alloy.
The density of aluminum is 2.70 g/cm3 (2,700 kg/m3, 0.0975 lb/in3) for high-purity grades. Common coil alloys sit close to that figure, from 2.66 g/cm3 for some 5xxx alloys to 2.73 g/cm3 for some 3xxx alloys. This page lists the Aluminum Association's nominal densities for twelve wrought alloys and shows how density turns coil dimensions into weight.
- 2.70 g/cm3 high purity
- 12 alloys tabulated
- g/cm3, kg/m3, lb/in3
What is the density of aluminum?
For high-purity aluminum the Aluminum Association lists a nominal density of 2.700 g/cm3, or 0.0975 lb/in3, for example for alloy 1185. In everyday use this is rounded to 2.70 g/cm3. Alloying changes the figure only slightly, so a value of 2.70 g/cm3 is a fair first estimate for any of the 1xxx, 3xxx and 5xxx alloys used for coil, and the alloy's own value is used when the weight has to be right.
Aluminum is a light metal. Structural steel is usually taken at close to three times the density of aluminum, which is why the same sheet area in aluminum weighs roughly a third as much as steel of the same thickness.
Aluminum alloy density table
The values below are the calculated nominal densities published by the Aluminum Association for each alloy. The kg/m3 column is the g/cm3 value multiplied by 1000.
| Alloy | Series | g/cm3 | kg/m3 | lb/in3 |
|---|---|---|---|---|
| 1050 | 1xxx | 2.705 | 2705 | 0.0975 |
| 1060 | 1xxx | 2.705 | 2705 | 0.0975 |
| 1100 | 1xxx | 2.71 | 2710 | 0.098 |
| 3003 | 3xxx | 2.73 | 2730 | 0.099 |
| 3004 | 3xxx | 2.72 | 2720 | 0.098 |
| 3005 | 3xxx | 2.73 | 2730 | 0.098 |
| 3105 | 3xxx | 2.72 | 2720 | 0.098 |
| 5005 | 5xxx | 2.70 | 2700 | 0.098 |
| 5052 | 5xxx | 2.68 | 2680 | 0.097 |
| 5754 | 5xxx | 2.67 | 2670 | 0.097 |
| 5083 | 5xxx | 2.66 | 2660 | 0.096 |
| 5086 | 5xxx | 2.66 | 2660 | 0.096 |
The Aluminum Association gives these as calculated nominal densities for weight calculations, not as engineering requirements. They are not guaranteed limits. The g/cm3 and lb/in3 figures are reproduced as published, each rounded separately, so converting one into the other will not always match the last digit. That is why 3003 and 3005, both listed at 2.73 g/cm3, show different lb/in3 values.
Why do aluminum alloy densities differ?
Each alloy is aluminum plus small, controlled amounts of other elements, and those elements change the density a little. The table shows the pattern for coil alloys:
- 1xxx, at least 99.00% aluminum: 2.705 to 2.71 g/cm3, close to high-purity aluminum.
- 3xxx, alloyed mainly with manganese: 2.72 to 2.73 g/cm3, slightly above the 1xxx alloys.
- 5xxx, alloyed mainly with magnesium: 2.66 to 2.70 g/cm3. The alloys with more magnesium have the lower values: 5005, with a magnesium range of 0.50 to 1.1%, is listed at 2.70 g/cm3, 5052 (2.2 to 2.8% magnesium) at 2.68 g/cm3, and 5083 (4.0 to 4.9% magnesium) at 2.66 g/cm3.
The full spread across the table is 0.07 g/cm3, about 2.6% of the high-purity value. That is small, but on a large order it adds up, so use the alloy's own density rather than a generic figure when the weight matters.
Converting aluminum density between units
Density units convert with plain arithmetic:
- g/cm3 to kg/m3: multiply by 1000. 2.70 g/cm3 is 2,700 kg/m3.
- From density to sheet weight per area: multiply by the thickness in meters. 2,700 kg/m3 at 1.00 mm (0.001 m) is 2.70 kg per square meter.
- g/cm3 to lb/in3: use the published lb/in3 value for the alloy where one is given, as in the table above.
A useful shortcut follows from the second line: in kg per square meter, the weight of aluminum sheet is its thickness in millimeters multiplied by its density in g/cm3. Sheet of 3105 at 0.50 mm weighs 0.50 x 2.72 = 1.36 kg per square meter.
How density sets coil weight and length
A coil is a long, thin strip, so its weight is thickness x width x length x density. Turned around, the length of strip on a coil of known weight is weight / (thickness x width x density). Density is the only material property in either formula, which is why the alloy matters when you estimate how many meters of strip a coil holds or how many coils fill a container.
Worked example, using 3105 at 2.72 g/cm3 (2,720 kg/m3):
- Strip 0.50 mm thick and 1000 mm wide weighs 0.0005 m x 1.0 m x 2,720 kg/m3 = 1.36 kg per meter of length.
- A 3,000 kg coil of that strip holds about 3,000 / 1.36 = 2,206 meters.
- The same coil in 5083, at 2.66 g/cm3, would hold about 3,000 / 1.33 = 2,256 meters.
The coil weight and length calculator runs these formulas for metric and imperial inputs, including outside diameter and weight per inch of width. If your drawing gives thickness as a gauge number, convert it first with the sheet metal gauge chart, because gauge numbers for aluminum and steel are not the same thickness.
Calculated weights are nominal and cover the bare metal; on prepainted coil the coating adds a small amount. Actual coil weight also depends on the thickness and width tolerances, the core and the packaging, so the shipping weight on the packing list is the figure to use for freight.
Density and the coil you order
Orbit melts, casts and rolls aluminum in Aqaba, Jordan, and supplies rolled aluminum coil in 1xxx, 3xxx and 5xxx series alloys from 0.20 to 2.00 mm thick, up to 1650 mm wide and up to 10 tonnes per coil. 3105 is the main substrate for coated coil. When you request a quote, state the alloy series or grade, thickness, width and the coil weight or inside and outside diameters your line can take, and the coil weight and strip length can be worked out from the density of the alloy supplied. Material certificates come with every batch.
Density is one of several physical properties that matter to coil users. The page on the melting point of aluminum covers another, and the guide to whether aluminum is magnetic explains how aluminum is told apart from steel in the shop and in scrap sorting.
Sources
- Aluminum Association, International Alloy Designations and Chemical Composition Limits for Wrought Aluminum and Wrought Aluminum Alloys (Teal Sheets), revised December 2025: calculated nominal densities and composition limits.
Density questions.
What is the density of aluminum in kg/m3?
About 2,700 kg/m3 for high-purity aluminum, which is 2.70 g/cm3 multiplied by 1000. Coil alloys range from about 2,660 kg/m3 for some 5xxx alloys to 2,730 kg/m3 for some 3xxx alloys.
What is the density of aluminum in lb/in3?
The Aluminum Association lists 0.0975 lb/in3 for high-purity aluminum and for 1050 and 1060. The other coil alloys in the table on this page range from 0.096 to 0.099 lb/in3.
What is the density of 3105 aluminum?
The Aluminum Association lists a calculated nominal density of 2.72 g/cm3, or 0.098 lb/in3, for 3105. It is a value for weight calculations, not an engineering requirement.
Does temper change the density of aluminum?
The Aluminum Association publishes one nominal density per alloy, not per temper, and that single value is the one used for coil and sheet weight calculations in every temper of the alloy.
Why is the 5xxx series lighter than the 3xxx series?
The published values show it: the 5xxx alloys, alloyed with magnesium, are listed at 2.66 to 2.70 g/cm3, and the alloys with the most magnesium have the lowest values. The 3xxx alloys, alloyed with manganese, are listed at 2.72 to 2.73 g/cm3.
Need coil weights worked out for your order?
Send the alloy, thickness, width, coil weight or diameters, quantity and destination. We respond to RFQs within one business day.
