Alloy 1xxx / 3xxx · PE / HDPE
Aluminum sign blanks start with flat coil and sheet.
Orbit supplies the coil and flat sheet that blank makers cut into aluminum sign blanks. Flat, consistent-surface stock in any RAL color, with coatings suited to indoor and outdoor signs.
- Alloy 1xxx / 3xxx
- PE / HDPE
- Leveled for flatness
Application
Flatness and color.
Consistent-gauge coil so panels and sign faces stay flat under lighting.
Related applications: License plates · ACP
Interior and exterior signs.
Coil arrives ready for fabrication and finishing, in your color reference.
Prepainted aluminum coilSign blank stock for blank makers
Orbit is a mill, not a sign blank shop. We cast, roll, coat, slit and cut to length, and we sell that material to the companies that make sign blanks. Finished, cut-to-size sign blanks are not part of the offer confirmed on this page, so ask in your RFQ if you need them. If you buy wholesale aluminum sign blanks for resale, a blank maker is usually the right supplier; if you make blanks, we supply the stock they are cut from.
The usual chain has three steps. Orbit supplies master coil, slit coil or flat sheet. The blank maker shears or punches that stock into finished aluminum blanks of the sizes its customers order. The sign shop then prints, applies vinyl or sheeting, and installs. Our job is to make the first step consistent, so the blank maker's cutting and the sign shop's graphics run without surprises. See slitting and cut-to-length for how coil becomes flat sheet.
Coil specification.
| Coatings | PE, Acrylic, HDPE, PVDF (or mill-finish) |
|---|---|
| Thickness | 0.20 to 2.00 mm rolled; up to 1.60 mm coated (sign gauge on request) |
| Width | Up to 1650 mm (coating up to 1350 mm) |
| Coil weight | Up to 10 tonnes |
| Minimum order | 6.5 MT (±10%) |
| Color | RAL or custom match (available) |
| Warranty | 5 to 20 years by application and environment |
Guidance
Recommended specification.
A typical starting point for coated sign-face coil.
| Alloy | 1xxx or 3xxx |
|---|---|
| Coating | PE or HDPE |
| Color | solid flat colors |
| Substrate-only | mill finish available |
| Thickness | Thickness is set by your specification and confirmed per order; Orbit rolls 0.20 to 2.00 mm, coated up to 1.60 mm. |
| Processing | leveling for flatness |
Exact alloy, gauge and coating are confirmed per order, share your spec in an RFQ.
What aluminum sign blanks need from the stock
Sign faces are often viewed close-up and under lighting, so surface flatness and color accuracy matter; any waviness or color drift is immediately visible. Aluminum gives a lightweight, corrosion-resistant base whose stiffness depends on alloy, temper and thickness; leveling delivers the flatness sign faces need.
Interior and short-life signage suits PE; long outdoor exposure favors PVDF. Larger sign faces can also be produced as ACP, see ACP.
Gauge and thickness
Sign blank thickness may be quoted in gauge numbers, decimal inches or millimeters, so state it in millimeters or decimal inches with a tolerance standard. Gauge numbers are not interchangeable between metals, because the same gauge number gives a different thickness in aluminum than in steel. Convert to millimeters before you order, using our sheet metal gauge chart. We do not recommend a gauge for a given sign. The thickness is set by the sign specification and by the blank maker's tooling, and we roll to the thickness you state within our 0.20 to 2.00 mm rolled range, up to 1.60 mm coated.
Coating and finish options
The coating is chosen by where the sign will hang and how long it has to look right. The sign substrate and coating guide covers the trade-offs in more depth.
| Option | Typical sign use |
|---|---|
| PE | Interior and short-life signs |
| HDPE | General exterior signs, moderate exposure |
| PVDF | Long outdoor exposure where color hold matters most |
| Acrylic | Available; suitability confirmed per order |
| Mill finish | Blank makers or sign shops that apply their own coating or sheeting |
Finishes include solid, matte and gloss, and an anti-graffiti finish is available for signs in public places where paint and marker need to come off without damaging the coating. Colors are matched to a RAL number or a custom sample.
Quality & compliance
Testing and documentation.
Certified management systems
Orbit's management systems are certified to ISO 9001 (quality), ISO 14001 (environment) and ISO 45001 (occupational health and safety).
Tests that matter here
Coated coil can be tested for gloss retention, color difference (delta E) and adhesion; test reports for a given order are available on request. See quality & certifications for how this is documented.
Documentation with the batch
Material certificates accompany every batch; ASTM and EN references are available on request.
Signage coil questions.
What aluminum is used for signs?
Signs use flat coated aluminum coil or sheet, finished in any RAL color.
Does Orbit sell finished sign blanks?
Not as a standard offer confirmed on this page. Ask in your RFQ if you need cut blanks; otherwise Orbit supplies the coil and sheet blank makers cut from.
What coating for outdoor signs?
PVDF is used for long outdoor life; PE suits interior or short-term signage.
Can you match brand colors?
Yes. Orbit matches any RAL or custom brand color.
What thickness is typical for signage?
Thickness is set by your specification and confirmed per order; Orbit rolls 0.20 to 2.00 mm, coated up to 1.60 mm.
Can I order mill-finish stock for sign blanks?
Yes. Mill-finish coil or sheet is available for blank makers and sign shops that apply their own coating or sheeting.
What is the minimum order?
The minimum order is 6.5 MT, plus or minus 10 percent.
What to send with your RFQ.
Include these and we can return a coil specification and quote without back-and-forth.
- Application and substrate (aluminum or steel)
- Alloy and temper, if known
- Gauge and coil width
- Coating system and color (a RAL number or a sample)
- Quantity and destination port
Our technical office reviews every RFQ and replies with a specification and quote. We respond to RFQs within one business day.
Sourcing sign stock?
Tell us interior or exterior, gauge and color, we will match the coating. Include your application, substrate (aluminum or steel), alloy, gauge, width, coating, color, quantity and destination. We respond to RFQs within one business day.


