Finish · Textured paint

Textured aluminum sheet and coil.

Textured aluminum sheet, as covered here, carries its texture in the paint film: the coating cures to a fine grain or wrinkle surface while the metal underneath stays flat. It tends to hide handling marks and reduce glare without changing the shape of the strip. Orbit applies textured finishes on coil it casts, rolls and coats in Aqaba, Jordan.

  • Coated coil up to 1.60 mm thick
  • Up to 1350 mm wide
  • RAL or custom color
  • MOQ 6.5 MT

What is a textured paint finish on aluminum?

A textured finish is a coil coating formulated to cure with a raised, uneven surface instead of a smooth one. The texture comes from the paint itself, for example from fine particles in the formulation or from a film that wrinkles as it cures. On a coil line it is applied and cured like any other topcoat, over pretreatment and primer.

The result looks and feels different from a smooth finish. It scatters light, so it reads as lower gloss, and the broken surface makes small scratches, fingerprints and handling marks harder to see. The strip itself is not reshaped: its thickness, flatness and stiffness are those of the bare coil.

How is textured paint different from embossing?

Both give a surface you can feel, but the texture sits in a different place. Embossing presses a pattern into the metal between patterned rolls, so the aluminum itself takes the shape. A textured paint finish leaves the metal flat and builds the texture into the coating film. Orbit does both. For a pattern rolled into the metal, see aluminum with a texture rolled into the metal.

Textured paint finish compared with embossed metal
PointTextured paint finishEmbossed metal
Where the texture sitsIn the coating filmIn the metal
Effect on stiffnessNone; metal stays flatCan add stiffness to thin coil
Supplied asCoated coil or sheetMill finish or coated
Typical reason to choose itAppearance, low glare, hiding marksStiffness, low glare, hiding marks

Where is textured aluminum sheet used?

Across the market, textured coated aluminum is chosen where a smooth, reflective surface would show marks or glare. Typical uses:

  • Cladding and facade panels: a low-sheen, mineral or stone-like look on large flat areas.
  • Interior wall and ceiling panels: surfaces that are handled during installation and seen up close.
  • Rolling shutters and doors: parts that rub and get touched in daily use.
  • Equipment housings and enclosures: panels where fingerprints and small scuffs would spoil a smooth color.

On exterior surfaces a textured film can hold dirt more readily than a smooth one, which is worth weighing for facades.

Textured sheet aluminum is cut from the same coated coil on Orbit's slitting and cut-to-length lines, so it can ship as master coil, slit coil or sheet. Textured is one of the aluminum coil finishes Orbit supplies.

Which coating systems carry a textured finish?

Texture is a property of the paint formulation, so whether a particular texture can be supplied depends on the coating system and the color. Orbit applies PE, HDPE, PVDF, PU, PUPA, Epoxy, Acrylic and Epoxy-PE systems, and confirms per order which of them can carry the texture you need. As with any finish, pick the system for the exposure first: the texture sets the look, while the resin sets how long color and gloss last outdoors.

Textured aluminum coil is part of Orbit's prepainted aluminum coil range, with the same sizes, alloys and documents as smooth finishes.

Orbit textured coated aluminum: confirmed supply data
SubstrateAluminum in 1xxx, 3xxx and 5xxx series alloys. 3105 is the main coated substrate.
Coated thicknessUp to 1.60 mm
Coated widthUp to 1350 mm
Coil weightUp to 10 tonnes
ColorRAL or custom color matching
Texture and coating systemConfirmed per order
Warranty5 to 20 years, depending on application and environment
Minimum order6.5 MT, typically 6 MT per color on coating

What to approve on a textured sample

Approve a coated sample before the production run, and judge it the way the finished part will be seen:

  • Texture type and coarseness: fine grain or wrinkle, and how pronounced, compared with your reference.
  • Color under agreed light: textured surfaces can read darker or lighter than a smooth panel of the same color, so match against a textured reference, not a smooth chip.
  • Gloss or sheen: the agreed level, measured or judged against the sample.
  • Forming: a test bend at your tightest radius, checked for cracking or a change in appearance at the bend.

Material certificates ship with every batch, and Orbit replies to an RFQ within one business day.

Textured finish questions.

What is textured aluminum sheet?

Here it means coated aluminum whose paint film cures to a fine grain or wrinkle surface. The texture is in the coating, and the metal underneath stays flat.

Is a textured finish the same as embossed aluminum?

No. Embossing rolls a pattern into the metal and can add stiffness. A textured finish builds the texture into the paint and leaves the metal flat. Orbit supplies both.

Why choose a textured finish over a smooth one?

A textured surface scatters light, so it shows less glare, and it makes small scratches, fingerprints and handling marks harder to see than on a smooth finish of the same color.

Which coating systems can carry a textured finish?

It depends on the paint formulation and the color. Orbit applies PE, HDPE, PVDF, PU, PUPA, Epoxy, Acrylic and Epoxy-PE systems and confirms per order which can carry the texture you need.

Can textured coated coil be formed after painting?

Coil coatings are designed to be formed after painting. How tight a bend the finish will take depends on the alloy, temper, thickness and coating system, so state the forming step in your RFQ.

What is the minimum order for a textured finish?

The minimum order is 6.5 MT, and coating is typically run at 6 MT per color.

Textured finish to quote?

Send the application, texture reference, color, alloy, thickness, width, quantity and destination. We respond to RFQs within one business day.

Request a Quote