Aluminum vs Steel Trailer Panels: Weight and Corrosion.
In the aluminum vs steel trailer panel decision, aluminum usually wins on weight and on freedom from rust, while steel is stiffer at the same thickness and usually resists dents better. The right choice depends on how the body is used, what it is exposed to on the road and in the wash bay, and how it will be repaired.
Key takeaways
- At the same thickness an aluminum panel weighs roughly a third as much as a steel one, but aluminum panels are often specified thicker, so the real saving is smaller.
- Aluminum does not rust. It can still corrode in wet contact with steel fasteners or frames, or under strongly alkaline cleaners.
- Steel panels resist dents better at equal thickness, but rust where the coating is broken.
- Prepainted aluminum gives a factory-cured finish on a substrate that will not bleed rust from scratches.
Aluminum vs steel trailer panels: how much weight is involved?
Using a typical density of 2.70 g/cm³ for aluminum and the conventional 7.85 g/cm³ for steel, an aluminum panel of the same size and thickness weighs roughly a third as much as a steel one. That is the starting point, not the answer.
Steel is stiffer and, in common grades, stronger than the aluminum alloys used for panels, so aluminum sidewall panels are often specified thicker to control dents and deflection. Panels are also only part of the body: the frame, posts, floor and running gear carry much of the weight. The saving on a finished trailer has to be worked out on the actual design. Whether it turns into more payload or lower fuel use depends on the operation, so we do not put a number on it here.
How do the panels behave in road salt and washing?
Steel panels depend on their coating. Painted or metallic-coated steel is protected while the coating is intact, but stone chips, scrapes and cut edges expose steel, and red rust can start there and stain the panel below. Winter road salt and coastal routes speed this up.
Aluminum forms a thin natural oxide film that protects it in near-neutral conditions, so a scratch does not rust. Two things can still attack it:
- Contact with steel. Wet contact with steel frames, stainless steel or copper fasteners can accelerate corrosion of the aluminum next to them. Isolating tapes, washers and compatible fasteners reduce the risk.
- Strong cleaners. Strong acids and strong alkalis attack the oxide film. Truck wash chemicals should be checked against the panel finish and rinsed off.
Coated aluminum adds a paint film over the oxide, which shifts the questions to cut edges and to corrosion that can creep under a damaged coating. Detailing at rivet lines and edges matters on both materials.
What happens when a panel is damaged?
Dents are the most visible difference. At equal thickness a steel panel usually resists denting better, mainly because the steel grades used for panels are typically stronger than the aluminum tempers used; steel's higher stiffness also reduces flexing. An aluminum panel of a harder temper and adequate thickness narrows that gap, which is one reason alloy, temper and gauge are chosen together.
Repair routes differ:
- Panel replacement. On riveted or bonded bodies, a damaged sheet section is often replaced rather than straightened. Both materials allow this.
- Welding. Steel can be repaired with common steel welding procedures. Aluminum welds need aluminum procedures, filler and equipment, and welding heat can reduce the strength gained by strain hardening near the weld.
- Refinishing. On prepainted panels, touch-up paint covers small damage. On steel, any rust has to be removed first or it spreads under the new paint.
Talk to the body builder or repair shop that will service the fleet. The best panel on paper is less useful if local shops cannot repair it.
How do the finishes compare?
Both materials can be supplied prepainted from coil, which gives a factory-cured, even finish before the panel is cut and fitted. Prepainted coil also gives a consistent base for vinyl graphics and fleet livery. The difference shows over time at damage: a scratch on painted steel can bleed rust, while a scratch on painted aluminum leaves bare aluminum, which does not rust.
Orbit's coil-coated aluminum is available up to 1.60 mm thick and 1350 mm wide, in PE, HDPE, PVDF, PU, PUPA, Epoxy, Acrylic and Epoxy-PE systems, with RAL or custom color matching. Warranty runs from 5 to 20 years depending on application and environment.
Which panel material suits which body?
- Aluminum tends to suit bodies where weight counts on every trip, where winter salt or coastal routes are routine, and where a clean painted appearance has to last.
- Steel tends to suit bodies that take heavy impact loading, where dent resistance at low thickness matters more than weight, and where the fleet's repair base works mainly in steel.
Where a body mixes materials, for example a steel frame with aluminum skins, isolate the two metals where they meet.
What should a trailer panel specification state?
- Alloy, temper and thickness, with the dent or stiffness requirement that sets them
- Coating system, color and gloss, and the reverse-side requirement
- Width and coil or sheet supply
- Fastening method and how dissimilar metals are isolated
- Wash chemicals the fleet uses
- Warranty expectations for the route and climate
Our page on aluminum for truck and trailer bodies sets out the alloys, coatings and supply forms Orbit offers for this application. Gauge and alloy for a given body are confirmed per order.
Common questions
Are aluminum trailer panels lighter than steel?
Yes. At the same size and thickness an aluminum panel weighs roughly a third as much as a steel one. Aluminum panels are often specified thicker for dent resistance, so the saving on a finished body is smaller than that ratio.
Do aluminum trailer panels corrode?
They do not rust, but they can corrode in wet contact with steel, stainless steel or copper, or when strong acid or alkaline cleaners attack the oxide film. Isolation and suitable wash chemicals reduce the risk.
Is steel more dent resistant than aluminum?
At equal thickness, usually yes, mainly because the steel grades used for panels are typically stronger than the aluminum tempers used; steel's higher stiffness also reduces flexing. Alloy, temper and thickness change the comparison, so specify the aluminum panel against the dent requirement.
Can aluminum trailer panels be repaired?
Yes. Damaged sections on riveted or bonded bodies are often replaced. Welding aluminum needs aluminum procedures and filler, and small paint damage can be touched up.
Does Orbit supply coil for trailer panels?
Yes. Truck and trailer panels are one of the applications Orbit serves, with prepainted aluminum coil up to 1.60 mm thick and 1350 mm wide. Gauge and alloy are confirmed per order.
References
- Densities: 2.70 g/cm³ is a typical value for aluminum and 7.85 g/cm³ the conventional design value for steel, used here for plain arithmetic only.
- Orbit Aluminum Industries: truck and trailer panels application page.
- Orbit Aluminum Industries: prepainted aluminum coil product page, for coated coil dimensions, coating systems and color matching.
Building trailer panels?
Send alloy, temper, gauge, width, coating system, color and quantity. We respond to RFQs within one business day.
