Galvalume vs Galvanized Steel: How the Coatings Differ.

Galvalume vs galvanized is a question about the metallic coating on the steel. Galvanized sheet carries a zinc coating; Galvalume-type sheet carries a coating of about 55% aluminum, about 43% zinc and a small silicon addition. Both are applied by hot dipping, and the difference shows in how each protects the steel, at cut edges and in heat.

Key takeaways

  • Galvanized steel has a zinc coating. Galvalume-type steel has a coating of about 55% aluminum, about 43% zinc and a small silicon addition.
  • ASTM A792 covers 55% aluminum-zinc alloy-coated steel sheet. Galvanized and galvannealed sheet are covered by a separate hot-dip zinc specification.
  • Zinc protects exposed steel by corroding first. The aluminum-zinc coating relies more on a barrier effect.
  • Which lasts longer depends on the exposure, the coating weight and the detailing. There is no single answer for every site.

Galvalume vs galvanized: what is actually on the steel?

Both products start as steel sheet that runs through a bath of molten metal. What differs is the bath. For galvanized sheet it is zinc. For Galvalume-type sheet it is an alloy of about 55% aluminum, about 43% zinc and a small silicon addition. Galvalume is a registered trademark of BIEC International, Inc., and the coating is also sold under other names, so specifications usually describe it by composition rather than by brand.

The two coatings compared. General description, not a specification.
PointGalvanized55% Al-Zn (Galvalume-type)
CoatingZincAbout 55% aluminum, about 43% zinc and a small silicon addition
ProcessHot dipHot dip
Main protectionSacrificial: zinc corrodes in place of the steelMainly barrier, with some sacrificial action from the zinc
US specificationHot-dip zinc and zinc-iron coated sheet specificationASTM A792

ASTM A792 covers 55% aluminum-zinc alloy-coated steel sheet in coils and cut lengths, intended for corrosion resistance, heat resistance or both. Hot-dip zinc-coated (galvanized) and zinc-iron alloy-coated (galvannealed) sheet sit in a separate ASTM specification.

What is galvannealed steel?

Galvannealed sheet starts as hot-dip galvanized sheet. It is then heated so the zinc coating alloys with iron from the steel, giving a matte, zinc-iron coating instead of a bright zinc one. It is a variant of galvanized, not of the aluminum-zinc product. For most building sheet the comparison buyers ask about is zinc against 55% aluminum-zinc.

How do the two coatings protect the steel?

Zinc is more active than steel in the galvanic series, so where the coating is scratched or cut, the zinc around the damage corrodes in place of the steel. This sacrificial action is the main reason galvanized steel tolerates small breaks in its coating. The trade-off is that the zinc is consumed as it works, so the coating weight sets how long the protection can last in a given exposure.

The aluminum-zinc coating works differently. The aluminum-rich part of the coating forms a protective oxide and acts mainly as a barrier, while the zinc-rich part still gives some sacrificial protection. How each coating performs depends on coating weight, the exposure and the paint system; ask the supplier for performance data for the exposure in question.

Which exposures change the answer?

Neither coating wins everywhere. The result in a given place depends on:

  • Atmosphere. Coastal salt, industrial pollution and humidity change how fast either coating is consumed.
  • Cut edges and fixings. Products with many cut edges, punched holes or site cuts lean on how the coating protects exposed steel.
  • Contact with other materials. Wet contact with dissimilar metals, or runoff from other metals, can attack either coating.
  • Heat. ASTM A792 covers sheet for corrosion resistance, heat resistance or both.
  • Paint. Once a paint system goes on top, the metallic coating becomes the second line of defense, and cut-edge behavior becomes the main difference.

Coating weight is ordered by designation under each specification. Comparing the two products only makes sense at a stated coating weight and in a stated exposure.

Where is each coating used?

Both are used for roofing, wall panels, rainware and other building components, bare or painted. Galvanized sheet is also used for general fabrication, framing and ducting. Aluminum-zinc coated sheet is used for roofing and wall sheet in atmospheric exposure. These are general patterns; the choice for a project still follows the exposure and the specification.

What changes when the steel is prepainted?

Coil coating adds pretreatment, primer and topcoat over the metallic layer. The paint carries color and much of the weathering performance, but the metallic coating still decides what happens where the paint is broken: at cut edges, scratches and fastener holes. Prepainted galvanized and prepainted aluminum-zinc steel are traded as PPGI and PPGL, and the comparison of PPGI and PPGL covers how the two behave once painted.

Orbit sells coated steel coil alongside its aluminum coil; see Orbit's steel coil page. Steel substrate details are confirmed per RFQ.

What should a buyer specify?

  • The metallic coating: zinc, zinc-iron or 55% aluminum-zinc
  • The specification and the coating weight designation under it
  • Steel grade, thickness and width
  • Surface treatment and oiling, if bare
  • For prepainted steel, the paint system, color, and topcoat and backcoat requirements
  • The exposure and the forming operation, so the supplier can comment on fit

Common questions

Is Galvalume the same as galvanized steel?

No. Galvanized steel is coated with zinc. Galvalume-type steel is coated with an alloy of about 55% aluminum, about 43% zinc and a small silicon addition. Both coatings are applied by hot dipping.

Which lasts longer, Galvalume or galvanized?

It depends on the coating weight, the exposure, the detailing and the paint system, so ask the supplier for performance data for the exposure in question.

What standard covers Galvalume-type steel?

ASTM A792 covers 55% aluminum-zinc alloy-coated steel sheet in coils and cut lengths, for corrosion resistance, heat resistance or both.

What is galvannealed steel?

Galvannealed steel is hot-dip galvanized sheet that is heated after coating so the zinc alloys with iron, giving a matte zinc-iron coating.

Does Orbit sell Galvalume or galvanized steel?

Orbit sells prepainted steel coil. The steel substrate is confirmed per RFQ, so state the metallic coating you need in your request.

References

  • ASTM International: ASTM A792/A792M, the specification covering 55% aluminum-zinc alloy-coated steel sheet in coils and cut lengths for corrosion resistance, heat resistance or both.
  • Orbit Aluminum Industries: prepainted steel coil product page.
  • Orbit Aluminum Industries: PPGI vs PPGL post, for the prepainted forms of both substrates.
Orbit is an integrated aluminum coil manufacturer in Aqaba, Jordan, family owned and operating since 1976, with recycling, casting, rolling and coil coating. We hold ISO 9001, ISO 14001 and ISO 45001.

Comparing coated coil substrates?

Send substrate, coating system, color, gauge, width and exposure. We respond to RFQs within one business day.

Request a Quote

The technical information in this article is prepared in good faith and verified against publicly available industry sources at the time of writing. Product specifications, applications and requirements can vary by project; always confirm current specifications directly with Orbit Aluminum Industries before purchasing or specifying. Orbit Aluminum Industries is not liable for decisions made or outcomes resulting from use of this content. See our Terms & Conditions.