5xxx Aluminum Coil: Where 5005, 5052 and 5754 Fit.
- 5005
- 5052
- 5754
5005, 5052 and 5754, the 5xxx alloys compared here, share magnesium as the main alloying element. They differ in how much of it they carry, and that difference is the practical starting point for choosing among them.
Key takeaways
- In 5xxx the main alloying element is magnesium.
- These alloys are not heat treatable. Magnesium and cold work together determine strength, and temper records the cold work.
- Magnesium content differs across 5005, 5052 and 5754. Check the composition limits and compare properties in the same temper.
- A stronger metal does not by itself make a large flat panel stiffer. Gauge, panel size, support spacing and stiffening govern deflection.
- Confirm alloy, temper and gauge against your specification, together with the coating.
What defines the 5xxx series?
Aluminum alloy designations use four digits, and the first digit identifies the alloy series. For the 5xxx series the main alloying element is magnesium. The Aluminum Association registers designations and composition limits in the Teal Sheets, which is the place to read the exact limits for each alloy.
The series cannot be hardened by heat treatment. Magnesium contributes to strength, and cold work adds to it. The H temper designations record how much cold work a coil has received, which is why temper belongs next to alloy on every line item.
How do 5005, 5052 and 5754 compare?
| Alloy | Magnesium, relative to the others | What to check | Read next |
|---|---|---|---|
| 5005 | Nominally lower than 5052 and 5754 | Properties in the temper you intend to order | Alloy series guide |
| 5052 | Nominally between 5005 and 5754 | Requirement tables for your temper and gauge | 5052 properties and finish |
| 5754 | Nominally higher than 5005 and 5052 | Composition limits and properties in your temper | 3003 and 5052 outdoors |
The table avoids ranking the three by strength on purpose. Strength depends on temper and thickness, so two alloys are comparable only in the same temper, read from the same tables.
When does a 5xxx alloy fit?
A starting rule: look at the 5xxx alloys when a 3xxx alloy in a workable temper does not give the strength or dent resistance the part needs, or when the specification asks for a magnesium alloy by name. Orbit supplies coil for rolling shutters, roofing, gutters and downspouts, cladding, ACP, signage, license plates and truck and trailer panels. The alloy for each should be checked against your specification.
Read the 3xxx guide alongside this one. The two groups overlap, and a side-by-side reading of the requirement tables can be the clearest way to see the trade-off for your gauge.
Does a stronger alloy give a stiffer panel?
Not by itself. Yield and tensile strength govern denting and permanent deformation. Deflection under load, the sag of a large flat panel for example, is governed by the elastic modulus, gauge, panel size, support spacing and stiffening features. The elastic modulus of the aluminum alloys is nearly the same, so moving from one alloy to another does not by itself stiffen a panel.
If a flat panel deflects too much, the first levers are thickness and stiffening, and the supplier can help you weigh them. The ACP specification guide and the 1xxx guide make the same point from different directions.
What does outdoor or coastal use change?
Alloy is one input to outdoor performance. Pretreatment, the coating system, cut edges, maintenance and installation also decide how a panel ages, and they apply to coastal sites as much as inland ones. State the exposure in the request, including distance from the shoreline if that applies, and ask the supplier which alloy and coating combination it recommends for it.
Orbit's warranty runs 5 to 20 years depending on application and environment, and the term should be checked against your specification.
How should forming be handled?
A temper with more cold work gives more strength and less formability, so a tight bend can call for a softer temper than a gentle one. Give the supplier the bend radius, the forming method and the part geometry instead of asking for a named alloy alone. A trial bend on sample coil is a practical check, and for coated coil the coating must survive the bend as well as the metal. The roll forming and roofing guide sets out the interaction between gauge, alloy and temper.
What should a 5xxx request include?
- Alloy, temper, thickness and width
- The standard you work to, ASTM or EN depending on your market
- The forming operation and bend radius if temper is open
- Coating system, color and finish
- Exposure and any warranty requirement
Send these in one request and Orbit replies within one business day.
Common questions
Is 5052 stronger than 5754?
It depends on temper. Compare them in the same temper using the requirement tables of the standard on your order, and the reported values on the certificate.
Are 5xxx alloys heat treatable?
No. Their strength comes from magnesium and cold work, and the temper designation records the cold work.
Which 5xxx alloys does Orbit roll?
Orbit rolls 1xxx, 3xxx and 5xxx series coil and confirms the grade per order. This post compares the 5xxx alloys 5005, 5052 and 5754. Temper, gauge and width should be checked against your specification.
Will a 5xxx alloy fix a panel that sags?
Not by itself, because the elastic modulus of the alloys is nearly the same. Thickness, panel size, support spacing and stiffening features govern deflection.
References
- The Aluminum Association: International Alloy Designations and Chemical Composition Limits for Wrought Aluminum and Wrought Aluminum Alloys (Teal Sheets): the registry of designations and composition limits.
- Orbit rolled aluminum coil: alloys and thickness range.
Need a magnesium alloy coil?
Send alloy and temper if known, gauge, width, quantity, forming operation and exposure. We reply within one business day.
