Aluminum Sheet vs Plate: Where the Thickness Line Falls.
The difference in aluminum sheet vs plate is thickness. In US practice, plate generally starts at 0.250 in (about 6.3 mm); flat-rolled aluminum thinner than that is sold as sheet, either flat or in coil. The word decides which tolerance tables, price lists and processing routes apply, so it is worth getting right on an order.
Key takeaways
- In US practice, aluminum plate generally starts at 0.250 in (about 6.3 mm). Thinner flat-rolled product is sheet.
- ASTM B209 covers flat sheet, coiled sheet and plate in one specification. Orders to EN standards are written against EN 485.
- Sheet is usually formed and often coated before forming. Plate is more often cut, machined and welded.
- Orbit rolls 0.20 to 2.00 mm, which is sheet territory, and supplies it as coil, slit coil or sheet cut to length.
Aluminum sheet vs plate: where does the line fall?
In US practice, plate generally starts at 0.250 in, which is about 6.3 mm. Below that thickness the product is sheet. The boundary is a convention, not a change in the metal: alloy and temper still govern strength and formability.
The word only tells you which side of a thickness line the product sits on. It does not replace a thickness on the order. Write the thickness as a number, in millimeters or inches, and let the word follow from it.
| Point | Sheet | Plate |
|---|---|---|
| Thickness (US practice) | Below 0.250 in (about 6.3 mm) | Generally from 0.250 in (about 6.3 mm) |
| Supply form | Coil, slit coil or flat sheet cut from coil | Flat pieces |
| Usual processing | Bending, roll forming, folding, stamping, coil coating | Sawing, machining, welding, heavier bending |
| US specification | ASTM B209 | ASTM B209 |
Which standards cover sheet and plate?
In US orders, one specification covers both. ASTM B209, Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate, covers flat sheet, coiled sheet and plate in the alloys and tempers listed in its tables. Dimensional tolerances for US aluminum sheet and plate are set in ANSI H35.2. Our guide to the ASTM sheet and plate standard walks through what it specifies and how it shows up on a mill test report.
Orders to EN standards are written against EN 485: part 1 for technical conditions of inspection and delivery, part 2 for mechanical properties, part 3 for tolerances on hot-rolled products and part 4 for tolerances on cold-rolled products. Composition sits in EN 573-3 and tempers in EN 515. Do not assume the US sheet and plate boundary carries over to an EN order. State the thickness in millimeters and the standard you are ordering to.
Tread plate, also called diamond plate in the trade, is a separate product. ASTM covers it in B632/B632M, not in B209, so a raised-pattern floor plate is not ordered as ordinary plate.
What is aluminum plate used for?
Plate is chosen when the part has to carry load in its own right, hold a machined feature or stay flat under its own weight. Typical uses include:
- Base plates, brackets and structural members
- Tooling, fixtures and machined components
- Tank, vessel and enclosure walls
- Marine and transport structures where thickness, not formability, sets the design
Plate is usually bought cut to size or in standard flat lengths. It is rarely coated on a coil line, because it is not handled as coil.
What is aluminum sheet used for?
Sheet is chosen when the part is formed from a flat blank. It is bent on a press brake, roll formed into a profile, folded into a cassette or stamped. Because it can be handled as coil, it can be coated before forming, so the part leaves the press already finished.
- Cladding and facade panels, roofing, gutters and downspouts
- Signage, license plates and composite panel skins
- Truck and trailer body panels
- Rolling shutter slats
How does sheet from coil fit into an order?
Sheet is often delivered as coil. A fabricator can take that coil whole, have it slit into narrower coils for a roll former, or have it cut into flat sheets of a set length.
Orbit's rolled coil range runs from 0.20 to 2.00 mm thick, up to 1650 mm wide, in coils up to 10 tonnes, in 1xxx, 3xxx and 5xxx alloys. That whole range sits well below the plate line of about 6.3 mm, so everything Orbit rolls is sheet. Coated coil is available up to 1.60 mm thick and 1350 mm wide.
When a shop needs flat blanks rather than coil, the coil goes through slitting and cut-to-length lines, so sheet can be supplied to the width and length the job needs. Sheet length, flatness and packing are confirmed per order.
Why order by thickness instead of gauge?
Gauge numbers are a shorthand for thickness, and they are not the same across metals. The same gauge number gives a different thickness for aluminum and for steel, so a drawing that gives only a gauge number, without naming the metal or the gauge system, can be read two ways. The aluminum and steel gauge table shows the conversions, but the safer habit is to write the thickness in millimeters or inches on the order and treat any gauge number as a reference only.
What should a sheet or plate order state?
- Alloy and temper
- Thickness as a number, with the unit, and the tolerance standard
- The specification: ASTM B209 or the relevant EN 485 parts
- Supply form: coil, slit coil, or flat sheet with width and length
- Finish: mill finish or coated, and if coated, the system and color
- Certificate requirements
Common questions
What thickness is aluminum plate?
In US practice, aluminum plate generally starts at 0.250 in, or about 6.3 mm. Flat-rolled aluminum thinner than that is sold as sheet. For orders to EN standards, state the thickness in millimeters rather than relying on the word.
Does ASTM B209 cover both sheet and plate?
Yes. ASTM B209 covers flat sheet, coiled sheet and plate in the alloys and tempers listed in its tables. Dimensional tolerances for US aluminum sheet and plate are set in ANSI H35.2.
Is tread plate the same as aluminum plate?
No. Tread plate, also called diamond plate, is covered by its own ASTM specification, B632/B632M, and is ordered as a separate product.
Does Orbit supply aluminum plate?
No. Orbit rolls 0.20 to 2.00 mm, which is sheet thickness. It supplies that as coil, slit coil or sheet cut to length, mill finish or coated.
Should I order aluminum sheet by gauge or by thickness?
By thickness. Gauge numbers give different thicknesses for aluminum and steel, so write the thickness in millimeters or inches and treat a gauge number as a reference only.
References
- ASTM International: ASTM B209/B209M, Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate: covers flat sheet, coiled sheet and plate.
- ANSI H35.2: dimensional tolerances for US aluminum sheet and plate.
- CEN: EN 485, parts 1 to 4: technical conditions for inspection and delivery, mechanical properties, and tolerances for hot-rolled and cold-rolled products.
- ASTM International: ASTM B632/B632M, the specification that covers aluminum tread plate.
- Orbit Aluminum Industries: rolled aluminum coil and slitting and cut-to-length product pages, for Orbit's thickness, width and supply forms.
Need sheet from coil?
Send alloy, temper, thickness, width, length or coil form, finish and quantity. We respond to RFQs within one business day.
